Circuit Description
The Throttle Position (TP) sensor circuit provides a voltage signal that changes relative to throttle blade angle. The signal voltage will vary from below 1.0 volt at closed throttle to above 4.0 volts at Wide Open Throttle (WOT). If the PCM detects a TP signal voltage that is intermittently less than the range of the TP sensor, DTC P1122 will be set.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
TP sensor intermittently indicates a throttle position signal less than 0.6 volt.
Action Taken When the DTC Sets
The PCM stores conditions which were present when the DTC set as Failure Records only. This information will not be stored as Freeze Frame Records.
Conditions for Clearing the MIL/DTC
| • | The DTC becomes history when the conditions for setting the DTC are no longer present. |
| • | The history DTC clears after 40 malfunction free warm-up cycles. |
| • | The PCM receives a clear code command from the scan tool. |
Diagnostic Aids
Inspect for the following conditions:
Many situations may lead to an intermittent condition. Perform each inspection or test as directed.
Important: : Remove any debris from the connector surfaces before servicing a component. Inspect the connector gaskets when diagnosing or replacing a component. Ensure that the gaskets are installed correctly. The gaskets prevent contaminate intrusion.
| • | Loose terminal connection |
| - | Use a corresponding mating terminal to test for proper tension. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair. |
| - | Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and faulty terminal to wire connection. Refer to Testing for Intermittent Conditions and Poor Connections , and to Connector Repairs in Wiring Systems for diagnosis and repair. |
| • | Damaged harness--Inspect the wiring harness for damage. If the harness inspection does not reveal a problem, observe the display on the scan tool while moving connectors and wiring harnesses related to the sensor. A change in the scan tool display may indicate the location of the fault. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair. |
| • | Inspect the powertrain control module (PCM) and the engine grounds for clean and secure connections. Refer to Wiring Repairs in Wiring Systems for diagnosis and repair. |
If the condition is determined to be intermittent, reviewing the Snapshot or Freeze Frame/Failure Records may be useful in determining when the DTC or condition was identified.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Powertrain On Board Diagnostic (OBD) System Check? | -- | ||
2 | Select DTC info and note if any other DTCs set. Is DTC P0122 also set? | -- | Go to DTC P0122 Throttle Position (TP) Sensor Circuit Low Voltage | |
3 | Is DTC P1107 also set? | -- | ||
4 | Test all 5 volt reference A circuits and connected components for an intermittant short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems . Did you find and correct the condition? | -- | ||
5 | Test the 5 volt reference circuit of the TP sensor for an intermittant open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems . Did you find and correct the condition? | -- | ||
6 | Test the signal circuit of the TP sensor for an intermittant short to ground, high resistance, or open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems . Did you find and correct the condition? | -- | ||
7 | Inspect for faulty connections at the harness connector of the TP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems . Did you find and correct the condition? | -- | ||
8 | Inspect for faulty connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems . Did you find and correct the condition? | -- | Go to Diagnostic Aids | |
9 |
Does the scan tool indicate DTC P1122 failed? | -- | System OK |
