Step | Action | Yes | No |
|---|---|---|---|
SCHEMATIC REFERENCE: Starting and Charging Schematics | |||
1 | Did you perform the Diagnostic System Check for starting and charging? | Go to Step 2 | |
2 | Turn the ignition to the START position. Does the engine crank? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 |
3 | Turn the ignition to the START position. Does the Theft Deterrent relay click? | Go to Step 4 | Go to Step 7 |
4 |
Does the test lamp illuminate? | Go to Step 5 | Go to Step 18 |
5 |
Does the engine crank? | Go to Step 13 | Go to Step 6 |
6 | Does the fuse in the jumper open? | Go to Step 19 | Go to Step 10 |
7 |
Does the test lamp illuminate? | Go to Step 8 | Go to Step 9 |
8 |
Does the test lamp illuminate? | Go to Step 13 | Go to Step 11 |
9 |
Does the test lamp illuminate? | Go to Step 14 | Go to Step 12 |
10 | Test the supply voltage circuit of the starter solenoid for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 24 | Go to Step 15 |
11 | Test the control circuit of the Theft Deterrent relay for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 24 | Go to Step 16 |
12 | Test the supply voltage circuit of the Theft Deterrent relay coil for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 24 | Go to Step 17 |
13 | Inspect for poor connections at the Theft Deterrent relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 24 | Go to Step 20 |
14 |
Did you find and correct the condition? | Go to Step 24 | Go to Step 21 |
15 | Inspect for poor connections at the starter solenoid. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 24 | Go to Step 22 |
16 | Inspect for poor connection at the Theft Deterrent Module harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 24 | Go to SECURITY Indicator Off, Engine Does Not Crank in Theft Deterrent |
17 | Inspect for poor connections at the ignition switch harness connector. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 24 | Go to Step 23 |
18 | Repair the open or high resistance in the supply voltage circuit of the Theft Deterrent relay switch circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 24 | -- |
19 | Repair the short to ground in the supply voltage circuit of the starter solenoid. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 24 | -- |
20 | Replace the Theft Deterrent relay. Refer to Theft Deterrent Relay Replacement in Theft Deterrent. Did you complete the replacement? | Go to Step 24 | -- |
21 | Replace the PNP switch. Refer to Park/Neutral Position Switch Replacement in Automatic Transaxle - 4T65 - E. Did you complete the replacement? | Go to Step 24 | -- |
22 | Replace the Starter Motor. Refer to Starter Motor Replacement . Did you complete the replacement? | Go to Step 24 | -- |
23 | Replace the Ignition Switch. Refer to Ignition Switch Assembly - Disassemble - Off Vehicle and Ignition Switch Assembly - Assemble - Off Vehicle in Instrument Panel, Gauges, and Console. Did you complete the replacement? | Go to Step 24 | -- |
24 | Operate the system for which the symptom occurred. Did you correct the condition? | System OK | Go to Step 2 |
