CAMPAIGN: AXLE SHAFT END PLAY CHECKING PROCEDURE
Model and Year: 1978-1980 Malibu, Monte Carlo and El Camino Models
TO: ALL CHEVROLET DEALERS
This supplemental bulletin contains additional revisions to the Claim Information section of "Chevrolet Dealer Service Bulletin" 8OC36, issued December, 1984. In additional a "ready reference" Service Procedure Chart is included for your convenience.
CLAIM INFORMATION
Submit a Claim with the information indicated below:
Parts Failed Parts Failure Labor Labor *Other Net Count Part No. Allowance Code Operation Hours Hours Amount ----- -------- --------- ---- --------- ----- ----- ------ 00 V2470 .3 .1
DESCRIPTION: Inspect axle code, no further action required.
Parts Failed Parts Failure Labor Labor *Other Net Count Part No. Allowance Code Operation Hours Hours Amount ----- -------- --------- ---- --------- ----- ----- ------ 00 V2471 .3 .1
DESCRIPTION: Inspect axle code and check end play.
Parts Failed Part's Failure Labor Labor *Other **Net Count Part No. Allowance Code Operation Hours Hours Amount ----- -------- --------- ----- --------- ----- ----- ------ 1 551651 00 V2472 .5 .1 8.88
DESCRIPTION: Inspect axle code, check end play and button thickness.
Parts Failed Parts Failure Labor Labor *Other **Net Count Part No. Allowance Code Operation Hours Hours Amount ----- ------- --------- ---- --------- ----- ----- -------
2 22507586 00 V2473 . 5 .1 8.88
DESCRIPTION: Inspect axle code, check end play and button thickness. Replace pinion shaft.
Parts Failed Parts Failure Labor Labor *Other **Net Count Part No. Allowance Code Operation Hours Hours Amount ------ ------- --------- ---- --------- ----- ----- ------ 3 551818 00 V2474 .8 . 1 8.88
DESCRIPTION: Inspect axle code, check end play and button thickness. Replace pinion shaft and one (1) rear axle shaft. Includes installing axle studs.
Parts Failed Parts Failure Labor Labor *Other **Net Count Part No. Allowance Code Operation Hours Hours Amount ----- --------- ---------- ---- --------- ----- ----- ------- 4 551818 00 V2475 .9 .1 8.88
DESCRIPTION: Inspect axle code, check end play and button thickness. Replace pinion shaft and two (2) rear axle shafts. Includes installing axle studs.
*Administrative Allowance.
Dealers will automatically receive the correct labor and material allowance based on the labor operation performed.
**The $8.88 in the "Net Amount Column" represents the material allowance for lubricant and/or lubricant additive, including 30%, used in con- junction with Labor Operation V2472, V2473, V2474 and V2475.
Refer to the Chevrolet Claims Processing Manual for details on Claim submission.
THIS "READY REFERENCE" CHART MAY BE USED IN CHECKING AND/OR REPLACING AXLE AND PINION SHAFTS
Vehicle Involved In 80-C-36 | | | "C" Type Check Code on Right Front Not "C" Axle -------------- Inboard Axle Tube (Steps 1 and 2)----- Type Axle-----| | | | | |------------------------------------| | | | | Mileage More Mileage Less | Than 20,000 Than 20,000 | | | | | | | | |---------------------------------| | | | | Use Dial Indicator to Check | | End Play of Each Axle | | (Steps 3,4,5 and 6) | | | | | | | | |------------------------------| | | | | | -------------------------|----------------------------------- | | Mileage End Play | | | | 20,000 to 30,000-------.030" or less or Greater than .030" | | 30,000 to 45,000-------.040" or less or Greater than .040" | | over 45,000 -------.055" or less or Greater than .055" | | | | | | | | | | | Remove Axle Cover and-----| | | Measure Axle Button | | thickness with Special | | Gage (Steps 8 and 9) | | | | | | | | | | | If Required, Replace Parts | | as Indicted on Chart II | | | | | | | | | | | Verify that Axle Shaft End | | Play is Less than Maximum | | Allowed on Chart III | | | | | | | | |--------------------| | | End Play End Play More | | Less Determine Cause | | | Contact Zone | | | | | | | | | | Install Completion Identification | Label (Step 13) --------------------
Chart II Pinion Shaft and Axle Shaft Replacement
Axle Shaft Button Thickness
Mileage Greater Than Less Than .190" .160" - .190" .160" ------- ------ ------------- -----
0 to 20,000 Replace Pinion Replace Pinion Replace Pinion Shaft Shaft & Axle Shaft
20,000 to No part Replace Pinion Replace Pinion 75,000 Replacement shaft & Axle Shaft
Over 75,000 No Part No Part Replace Pinion Replacement Replacement & Axle Shaft
Chart III Maximum Allowable End Play for Either Axle Shaft
Mileage Standard Axle Limited Slip --------- -------------- ------------
to 45,000 .040 .065 over 45,000 .055 .085
General Motors bulletins are intended for use by professional technicians, not a "do-it-yourselfer". They are written to inform those technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions and know-how to do a job properly and safely. If a condition is described, do not assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See a General Motors dealer servicing your brand of General Motors vehicle for information on whether your vehicle may benefit from the information.
