In order to overhaul, follow the sequence below.

1. Torque Converter Assembly Removal
2. Transmission Holding Fixture Assemble
3. Stub Shaft Removal
4. Output Speed Sensor Removal
5. Automatic Transmission Fluid Pan and Gasket Removal
6. Automatic Transmission Fluid Filter, Seal, and Level Control Valve Removal
7. Oil Feed Pipes Removal
8. Intermediate/Fourth Servo Removal
9. Low and Reverse Servo Removal
10. Control Valve Body Cover Removal
11. Oil Pump and Oil Pump Shaft Removal
12. Wire Harness Disconnect
13. Transmission Fluid Pressure Switch Removal
14. Control Valve Body Assembly and Gasket Removal
15. Spacer Plate and Gasket Removal
16. Checkball Removal
17. Manual Valve Clip Removal
18. Channel Plate and Gasket Removal
19. Accumulator Spring Removal
20. Output Shaft Sleeve Removal
21. Drive Sprocket, Driven Sprocket, and Drive Link Removal
22. Input Speed Sensor Removal
23. Wiring Harness Removal
24. Driven Sprocket Support Assembly Removal
25. Second Clutch Plates Removal
26. Reverse Input Clutch Housing Removal
27. Intermediate Fourth Band Removal
28. Direct/Coast Clutch and Reaction Gear Set Removal
29. Input Carrier and Reaction Gear Assembly Removal
30. Input Internal Gear, Forward Clutch Hub Removal
31. Forward Clutch and Low/Reverse Band Removal
32. Forward Clutch Support, Low Roller Clutch Removal
33. Output Shaft and Final Drive Assembly Removal
34. Final Drive Internal Gear Removal
35. Manual Shift Shaft Pin, Detent Lever, and Park Pawl Actuator Assembly Removal
36. Transmission Cooler Line Seals Removal
37. Torque Converter Seal Removal
38. Drive Sprocket Support Removal
39. Right Hand Axle Seal Removal
40. Case Inspection
41. Actuator Guide Replacement
42. Drive Sprocket Support Installation
43. Torque Converter Seal Installation
44. Transmission Cooler Line Seals Installation
45. Manual Shift Shaft Pin, Detent Lever, and Park Pawl Actuator Assembly Installation
46. Final Drive Assembly Disassemble
47. Final Drive Assembly Assemble
48. Final Drive Pinion End Play Check
49. Fretting Ring, Final Drive Internal Gear Install
50. Final Drive and Differential Assembly Install
51. Forward Clutch Support, Roller Clutch Disassemble
52. Forward Clutch Support, Low Roller Clutch Assemble
53. Forward Clutch Support, Low Roller Clutch Install
54. Forward Clutch Assembly Disassemble
55. Forward Clutch Assembly Assemble
56. Forward Clutch Functional Air Check
57. Low/Reverse Band Installation
58. Forward Clutch Assembly Installation
59. Input Internal Gear, Forward Clutch Hub Disassemble
60. Input Internal Gear, Forward Clutch Hub Assemble
61. Input Internal Gear, Forward Clutch Hub Install
62. Reaction Internal Gear, Input Carrier Disassemble
63. Input Carrier Pinion Gear Clearance Check
64. Reaction Internal Gear, Input Carrier Assemble
65. Reaction Internal Gear, Input Carrier Installation
66. Direct/Coast Clutch, Reaction Carrier Disassemble
67. Reaction Carrier Pinion Clearance Check
68. Direct/Coast Clutch, Reaction Carrier Assemble
69. Direct and Coast Clutch Functional Air Checks
70. Direct/Coast Clutch, Reaction Carrier Installation
71. Selective Washer Measurement and Installation
72. Reverse Input and Second Roller Clutch Disassemble
73. Reverse Input and Second Roller Clutch Assemble
74. Reverse Clutch Functional Air Check
75. Reverse Input and Second Roller Clutch Installation
76. Intermediate Fourth Band Assembly Installation
77. Second Clutch Plate Installation
78. Driven Sprocket Support Assembly Disassemble
79. Drive Sprocket Support Assemble
80. Second Clutch Functional Air Check
81. Driven Sprocket Support Assembly Installation
82. Wiring Harness Connection
83. Input Speed Sensor Installation
84. Drive Sprocket, Driven Sprocket, and Drive Link Disassemble
85. Drive Sprocket, Driven Sprocket, and Drive Link Assemble
86. Drive Sprocket, Driven Sprocket, and Drive Link Installation
87. Channel Plate Assembly Disassemble
88. Channel Plate Assembly Assemble
89. Accumulator Springs Installation
90. Channel Plate Assembly Installation
91. Manual Valve Link Installation
92. Checkballs Installation
93. Spacer Plate and Gaskets Installation
94. Control Valve Body Disassemble
95. Control Valve Body Assemble
96. Control Valve Assembly and Transmission Fluid Pressure Switch Installation
97. Wiring Harness Assembly Connect
98. Oil Pump Cleaning and Inspection
99. Oil Pump Assembly Installation
100. Side Cover/Gaskets, Disassemble, Assemble, Install
101. Output Shaft Sleeve Assemble
102. Output Shaft and Sleeve Assembly Installation
103. Side Cover Axle Seal Installation
104. Stub Shaft Sleeve Assembly Installation
105. Right Hand Axle Seal Assemble
106. Vehicle Speed Sensor Installation
107. Inter Fourth Servo Disassemble, Assemble, and Install
108. Intermediate/Fourth Servo Disassemble
109. Intermediate/Fourth Servo Assemble and Installation
110. Low/Reverse Servo Disassemble, Assemble, Install
111. Low and Reverse Servo Disassemble
112. Low and Reverse Servo Assemble and Installation
113. Oil Feed Pipes Assemble
114. Filter Assembly and Seal Installation
115. Oil Level Control Valve Installation
116. Automatic Transmission Fluid Pan and Gasket Installation
117. Torque Converter Installation