Circuit Description
The Powertrain Control Module (PCM) controls the air entering into the engine with an idle air control (IAC) valve. To increase the idle RPM, the PCM commands the pintle inside of the IAC valve away from the throttle body seat. This allows more air to bypass through the throttle blade. To decrease the RPM, the PCM commands the pintle towards the throttle body seat. This reduces the amount of air bypassing the throttle blade. A scan tool will read the IAC valve pintle position in counts. The higher the counts, the greater the airflow that bypasses the throttle blade.
Conditions for Setting the DTC
| • | DTC(s) P0106, P0107, P0108, P0112, P0113, P0117, P0118, P0121, P0122, P0123, P0125, P0131, P0132, P0133, P0134, P0200, P0335, P0341, P0342, P0401, P0440, P0442, P0446, P0502, P0503, P1133, P1336, P1404 and P1441 are not set |
| • | The BARO is greater than 72 kPa. |
| • | The Engine Coolant Temperature ( ECT) is greater than 40°C (104°F). |
| • | The engine RPM is below the desired RPM by more than 60 RPM for 13 seconds. |
| • | The engine has been running more than 20 seconds. |
| • | Throttle Position (TP) angle is less than 1 percent. |
| • | The IAC command is greater than 150 counts. |
Action Taken When the DTC Sets
| • | The malfunction indicator lamp (MIL) will illuminate after two consecutive ignition cycles in which the diagnostic runs with the malfunction present. |
| • | The PCM will record the operating conditions at the time that the diagnostic fails. This information will store in the Freeze Frame and Failure Records buffers. |
| • | A history DTC stores. |
| • | The coolant fan turns ON. |
Conditions for Clearing the MIL/DTC
| • | The MIL will turn OFF after three consecutive ignition cycles in which the diagnostic runs without a fault. |
| • | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
| • | The MIL/DTCs can be cleared by using the scan tool. |
Diagnostic Aids
| • | Inspect the IAC valve electrical connection for proper mating. |
| • | Inspect the wiring harness for damage. |
| • | Inspect the throttle stop screw for signs of tampering. |
| • | Inspect the throttle linkage for signs of binding or excessive wear. |
| • | A slow or unstable idle may be caused by one of the following conditions: |
| - | A too rich or a too lean fuel system |
| - | Foreign material in the throttle body bore or in the air induction system |
| - | A leaking or a restricted intake manifold |
| - | A leaking EGR valve |
| - | Excessive engine overloading. Check for seized pulleys, pumps, or motors on the accessory drive. |
| - | An engine oil that is too thick in viscosity. |
| • | Refer to Rough, Unstable, or Incorrect Idle and Stalling . |
Test Description
The number(s) below refer(s) to the step number(s) on the Diagnostic Table.
-
The Powertrain OBD System Check prompts you to complete some of the basic checks and to store the freeze frame and failure records data on the scan tool if applicable. This creates an electronic copy of the data captured when the fault occurred. The scan tool stores this data for later reference.
-
A normally operating IAC system will be able to be extended and retracted by a scan tool and change the engine idle RPM. The valve movement is verified by an engine RPM change.
-
If the scan tool was able to command the IAC valve smoothly, a malfunction may still exist internally within the IAC valve. You can check this by checking the internal resistance of the IAC valve.
-
The IAC circuits always have ground or voltage signals on them in pairs. If the test light illuminates on more or less than 2 terminals, 1 of the circuits is shorted to voltage or open.
-
The IAC circuits always have ground or voltage signals on them in pairs. If the test light illuminates on more or less than 2 terminals, 1 of the circuits is shorted to ground or open.
-
The IAC circuits are constantly switched between ground and voltage. The test light should blink on all circuits when connected to ground.
-
Thoroughly check any suspected circuitry for the following conditions:
-
A test light that remains ON constantly indicates that the circuit is shorted to the voltage.
-
Reprogram the replacement PCM and perform the crankshaft position system variation learning procedure. Refer to the latest Techline information for PCM programming and Powertrain Control Module (PCM) for the crankshaft position system variation learning procedure.
-
If no malfunctions have been present at this point and no additional DTCs were set, refer to Diagnostic Aids for additional checks and information.
| • | Backed out terminals |
| • | Improper mating |
| • | Broken locks |
| • | Improperly formed or damaged terminals |
| • | Poor terminal to wiring connections |
| • | Physical damage to the wiring harness |
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
Did you perform the Powertrain On-Board Diagnostic (OBD) System Check? | -- | |||
Does the engine RPM change smoothly when the engine is commanded by the scan tool? | 900-2000 RPM | |||
Are the resistances across terminals A and B and terminals C and D within the specified value? | 40-80ohms | |||
4 |
Are the resistances across terminals B and C and terminals A and D infinite? | -- | ||
Does the test light illuminate on 2 terminals? | -- | |||
With a test light connected to B+, probe the IAC electrical connector terminals. Does the test light illuminate on 2 terminals? | -- | |||
7 | Check for an open or a short to ground in the IAC valve high and low circuits and repair the circuits as necessary. Was a repair necessary? | -- | ||
Does the test light flash ON and OFF for all terminals? | -- | |||
9 | Check for an open or a short to voltage in the IAC valve high and low circuits and repair the circuits as necessary. Was a repair necessary? | -- | ||
Check the PCM electrical connector for poor connections and repair the connector as necessary. Was a repair necessary? | -- | |||
11 | Inspect the IAC valve passages. Was a problem found? | -- | ||
Did the test light remain ON constantly for the terminals that did not blink? | -- | |||
13 | Replace the IAC valve. Is the action complete? | -- | -- | |
Replace the PCM. Is the action complete? | -- | -- | ||
15 |
Does the scan tool indicate that this diagnostic has ran and passed? | -- | ||
Check to see if any additional DTCs are set. Does the scan tool display any DTCs that you have not diagnosed? | -- | Go to applicable DTC table | System OK Refer to Diagnostic Aids |
