Refer to
Cell 21: Engine Data Sensors
Circuit Description
The Throttle Position (TP) Sensor circuit provides a voltage signal that changes relative to throttle blade angle. The signal voltage will vary from below 1.0 volt at closed throttle to above 4.0 volts at Wide Open Throttle (WOT). If the PCM detects an excessively low TP Sensor voltage, DTC P0122 will be set.
Conditions for Setting the DTC
| • | The ignition is on. |
| • | TP sensor signal voltage is less than 0.1 volts for more than 9.5 seconds. |
Action Taken When the DTC Sets
| • | The PCM will illuminate the malfunction indicator lamp (MIL) during the first trip in which the diagnostic runs and fails. |
| • | If equipped with traction control, the PCM will command the EBTCM via the serial data circuit to turn OFF traction control and illuminate the TRACTION OFF lamp. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn OFF the MIL during the third consecutive trip in which the diagnostic has been run and passed. |
| • | The History DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool. |
Diagnostic Aids
Check for the following conditions:
| • | Poor connection at PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection. Use a corresponding mating terminal to test for proper tension. Refer to Intermittents and Poor Connections Diagnosis Repairing Connector Terminals and Connector Repairs . |
| • | Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, observe the throttle position display on the scan tool while moving connectors and wiring harnesses related to the TP sensor. A change in the display will indicate the location of the fault. Refer to Wiring Repairs . |
If DTC P0122 cannot be duplicated, the information included in the Fail Records data can be useful in determining vehicle mileage since the DTC was last set. If it is determined that the DTC occurs intermittently, performing DTC P1122 Throttle Position (TP) Sensor Circuit Intermittent Low Voltage diagnostic may isolate the cause of the malfunction.
Test Description
The numbers below refer to the step numbers on the diagnostic table:
Step | Action | Values | Yes | No |
|---|---|---|---|---|
1 | Did you perform the OBD Diagnostic System Check? | -- | ||
2 | If P1635 is also set, perform DTC P1635 5 Volt Reference Circuit first.
Does the scan tool indicate that the TP voltage parameter is less than the specified value? | 0.16V | ||
3 |
Does the scan tool indicate DTC P0122 failed? | -- | Go to Diagnostic Aids | |
4 |
Does the scan tool indicate that the TP voltage parameter is equal to the specified value? | 5V | ||
5 |
Does the voltage measure equal to the specified value? | 5V | ||
6 | Test the 5 volt reference circuit of the TP sensor for high resistance or an open and all 5 volt reference A circuits and connected components for a short to ground. Refer to Wiring Repairs . Did you find and correct the condition? | -- | ||
7 | Test the signal circuit of the TP sensor for a short to ground, a high resistance, or an open. Refer to Wiring Repairs . Did you find and correct the condition? | -- | ||
8 | Inspect for poor connections at the harness connector of the PCM. Refer to Intermittents and Poor Connections Diagnosis . Did you find and correct the condition? | -- | ||
9 | Inspect for poor connections at the harness connector of the TP sensor. Refer to Intermittents and Poor Connections Diagnosis and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | ||
10 | Replace the TP sensor. Refer to Throttle Position Sensor Replacement Did you complete the replacement? | -- | -- | |
|
Important: The replacement PCM must be programmed. Replace the PCM. Refer to Powertrain Control Module Replacement/Programming .Did you complete the replacement? | -- | -- | ||
12 |
Does the scan tool indicate DTC P0122 failed? | -- | System OK |
