DTC P0503 Vehicle Speed Sensor (VSS) Circuit Intermittent. Chevrolet Malibu 1999

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1999 🢒 Malibu 🢒 Engine 🢒 Engine Controls - 3.1L 🢒 DTC P0503 Vehicle Speed Sensor (VSS) Circuit Intermittent

DTC P0503 Vehicle Speed Sensor (VSS) Circuit Intermittent 2.4L

Automatic Transmission Components
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

The automatic transmission output (shaft) speed sensor (A/T OSS) provides vehicle speed information to the PCM. The A/T OSS is a permanent magnet (PM) generator mounted to the transmission case. The PM generator produces an AC voltage as the transmission speed sensor rotor teeth pass through the sensor's magnetic field. The AC voltage level increases as the speed of the vehicle increases. The PCM converts the AC voltage into a digital signal. The PCM uses the vehicle speed signal to determine shift timing, torque converter clutch (TCC) apply, TCC release, and gear ratio calculations.

When the PCM detects a loss of vehicle speed while the vehicle is in motion, then DTC P0503 sets. DTC P0503 is a type B DTC.

Conditions for Running the DTC

•	No TFP manual valve position switch DTC P1810.

•	The engine is running.

•	The time since the gear select lever change is greater than 6 seconds.

Conditions for Setting the DTC

Output speed drops greater than 1,200 RPM for 3 seconds.

Action Taken When the DTC Sets

•	The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.

•	The PCM commands maximum line pressure.

•	The PCM freezes shift adapts from being updated.

•	The PCM calculates output speed from input speed, engine speed, and commanded gear.

•	The PCM stores DTC P0503 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC

•	The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

•	A scan tool clears the DTC from PCM history.

•	The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

•	The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids

•	The condition may be intermittent. Inspect for a loose A/T OSS, or faulty sensor connection.

•	Inspect the wiring at the PCM and at the A/T OSS 2-way connector for the following conditions:

-	A backed out terminal

-	A damaged terminal

-	Reduced terminal tension

-	A chafed wire

-	A broken wire inside the insulation

-	Moisture intrusion

Corrosion

•	When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change.

•	Inspect for a damaged A/T OSS. Inspect for damaged transmission rotor teeth.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step tests the ability of the A/T OSS to produce an AC current. This step also verifies the integrity of the wiring to the PCM.

This step tests the A/T OSS circuit for correct resistance.

DTC P0503 Vehicle Speed Sensor Circuit -- Intermittent (2.4L)

Step

Action

Value(s)

Yes

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Install the Scan Tool .
Turn the ignition switch to the RUN position.

Important: Before clearing the DTCs, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM.

Record the Freeze Frame and Failure Records.
Clear the DTCs.

Notice: Support the lower control arms in the normal horizontal position in order to avoid damage to the drive axles. Do not operate the vehicle in gear with the wheels hanging down at full travel.

Raise and support the drive wheels.
Start and idle the engine.
Place the transmission in DRIVE.

With the drive wheels rotating, does the transmission output speed increase when the wheel speed increases?

Go to Diagnostic Aids

Go to Step 3

Turn the ignition switch OFF.
Disconnect the C1 and C2 PCM connectors
Using the J 35616-A connector test adapter kit, connect the J 39200 digital multimeter (DMM) between PCM terminals C1-64 and C2-61.
Select AC volts.
Turn the ignition switch to the RUN position.
Rotate the right front drive wheel by hand.
Observe the J 39200 DMM display.

Can a voltage greater than the specified value be obtained?

0.5 V AC

Go to Step 15

Go to Step 4

Select ohms on the J 39200 DMM in order to measure circuit resistance.

Is the circuit resistance within the specified range?

1,530 - 1,870 ohms

Go to Step 8

Go to Step 5

Is the circuit resistance greater than the specified value?

1,870 ohms

Go to Step 11

Go to Step 6

Leave the J 39200 DMM test leads connected.
Disconnect the A/T OSS connector at the transmission.

Is the circuit resistance less than the specified value?

1,530 ohms

Go to Step 7

Go to Step 14

Inspect circuits 400 and 401 for being shorted together.

Refer to General Electrical Diagnosis in Wiring Systems.

Was the condition found?

Go to Step 13

Inspect circuit 400 for a short to ground.

Refer to General Electrical Diagnosis in Wiring Systems.

Was the condition found?

Go to Step 13

Go to Step 9

Reconnect the C1 and C2 PCM connectors.
Select DC volts.
Using the J 35616-A connector test adapter kit, connect the J 39200 DMM test leads to terminals A and B of the A/T OSS connector end.
Turn the ignition switch to the RUN position.

Does the J 39200 DMM display system voltage?

Go to Step 10

Go to Step 12

Inspect circuit 400 for a short to power.

Refer to General Electrical Diagnosis in Wiring Systems.

Was the condition found?

Go to Step 13

Inspect circuit 400 for an open.
Inspect circuit 401 for an open.

Refer to General Electrical Diagnosis in Wiring Systems.

Was a condition found?

Go to Step 13

Go to Step 14

Remove the A/T OSS. Refer to Vehicle Speed Sensor Replacement .
Inspect the A/T OSS and the transmission for the following:

•	Incorrect A/T OSS

•	A/T OSS damage

•	Excessive A/T OSS to speed sensor rotor gap

•	Incorrect speed sensor rotor alignment

•	Speed sensor rotor damage

Repair any of the above items as necessary.

Is the repair complete?

Go to Step 16

Repair the wiring as necessary.

Refer to Wiring Repairs in Wiring Systems.

Is the repair complete?

Go to Step 16

Replace the A/T OSS.

Refer to Vehicle Speed Sensor Replacement .

Is the replacement complete?

Go to Step 16

Replace the PCM.

Refer to Powertrain Control Module Replacement/Programming in Engine Controls.

Is the replacement complete?

Go to Step 16

Perform the following procedure in order to verify the repair:

Select DTC.
Select Clear Info.
Road test the vehicle and ensure that the A/T OSS operates.
Select Specific DTC.
Enter DTC P0503.

Has the test run and passed?

System OK

Go to Step 1

DTC P0503 Vehicle Speed Sensor (VSS) Circuit Intermittent 3.1L

Automatic Transmission Components
Automatic Transmission Controls Schematics
OBD II Symbol Description Notice
Handling ESD Sensitive Parts Notice

Circuit Description

When the PCM detects a loss of vehicle speed while the vehicle is in motion, then DTC P0503 sets. DTC P0503 is a type B DTC.

Conditions for Running the DTC

•	No TFP manual valve position switch DTC P1810.

•	The engine is running.

•	The time since the gear select lever change is greater than 6 seconds.

Conditions for Setting the DTC

Output speed drops greater than 1,200 RPM within 3 seconds.

Action Taken When the DTC Sets

•	The PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met.

•	The PCM commands maximum line pressure.

•	The PCM freezes shift adapts from being updated.

•	The PCM calculates output speed from input speed, engine speed, and commanded gear.

•	The PCM stores DTC P0503 in PCM history during the second consecutive trip in which the Conditions for Setting the DTC are met.

Conditions for Clearing the MIL/DTC

•	The PCM turns OFF the MIL during the third consecutive trip in which the diagnostic test runs and passes.

•	A scan tool clears the DTC from PCM history.

•	The PCM clears the DTC from PCM history if the vehicle completes 40 warm-up cycles without an emission-related diagnostic fault occurring.

•	The PCM cancels the DTC default actions when the fault no longer exists and the ignition switch is OFF long enough in order to power down the PCM.

Diagnostic Aids

•	The condition may be intermittent. Inspect for a loose A/T OSS, or faulty sensor connection.

•	Inspect the wiring at the PCM and at the A/T OSS 2-way connector for the following conditions:

-	A backed out terminal

-	A damaged terminal

-	Reduced terminal tension

-	A chafed wire

-	A broken wire inside the insulation

-	Moisture intrusion

Corrosion

•	When diagnosing for an intermittent short or open condition, massage the wiring harness while watching the test equipment for a change.

•	Inspect for a damaged A/T OSS. Inspect for damaged transmission rotor teeth.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step tests the ability of the A/T OSS to produce an AC current. This step also verifies the integrity of the wiring to the PCM.

This step tests the A/T OSS circuit for correct resistance.

DTC P0503 Vehicle Speed Sensor Circuit -- Intermittent (3.1L)

Step

Action

Value(s)

Yes

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Install the Scan Tool .
Turn the ignition switch to the RUN position.

Record the Freeze Frame and Failure Records.
Clear the DTCs.

Raise and support the drive wheels.
Start and idle the engine.
Place the transmission in DRIVE.

With the drive wheels rotating, does the transmission output speed increase when the wheel speed increases?

Go to Diagnostic Aids

Go to Step 3

Turn the ignition switch OFF.
Disconnect the C1 PCM connector.
Using the J 35616-A connector test adapter kit, connect the J 39200 digital multimeter (DMM) between PCM terminals C1-64 and C1-65.
Select AC volts.
Turn the ignition switch to the RUN position.
Rotate the right front drive wheel by hand.
Observe the J 39200 DMM display.

Can a voltage greater than the specified value be obtained?

0.5 V AC

Go to Step 15

Go to Step 4

Select ohms on the J 39200 DMM in order to measure circuit resistance.

Is the circuit resistance within the specified range?

1,530 - 1,870 ohms

Go to Step 8

Go to Step 5

Is the circuit resistance greater than the specified value?

1,870 ohms

Go to Step 11

Go to Step 6

Leave the J 39200 DMM test leads connected.
Disconnect the A/T OSS connector at the transmission.

Is the circuit resistance less than the specified value?

1,530 ohms

Go to Step 7

Go to Step 14

Inspect circuits 400 and 401 for being shorted together.

Refer to General Electrical Diagnosis in Wiring Systems.

Was the condition found?

Go to Step 13

Inspect circuit 400 for a short to ground.

Refer to General Electrical Diagnosis in Wiring Systems.

Was the condition found?

Go to Step 13

Go to Step 9

Reconnect the C1 PCM connector.
Select DC volts.
Using the J 35616-A , connect the J 39200 DMM test leads to terminals A and B of the A/T OSS connector end.
Turn the ignition switch to the RUN position.

Does the J 39200 DMM display system voltage?

Go to Step 10

Go to Step 12

Inspect circuit 400 for a short to power.

Refer to General Electrical Diagnosis in Wiring Systems.

Was the condition found?

Go to Step 13