Circuit Description
The fog lamp relay is controlled by the body control module (BCM). Positive voltage is applied to the relay coil when the headlamp switch is in the park or head position. The BCM grounds the fog lamp relay control circuit in order to turn on the fog lamp relay. When the fog lamp relay control circuit becomes shorted to battery positive voltage, DTC B2533 is set.
Conditions for Running the DTC
| • | The ignition switch is in the on position. |
| • | The headlamp switch is in the on position. |
Conditions for Setting the DTC
All of the following conditions must be met:
| • | The ignition switch is in the on position. |
| • | The headlamp switch is in the PARK or HEAD position. |
| • | The fog lamp relay control circuit is shorted to battery positive voltage for 250 milliseconds. |
Action Taken When the DTC Sets
| • | DTC B2533 is stored in the BCM memory. |
| • | The fog lamps are inoperative when the headlamps or park lamps are on. |
Conditions for Clearing the DTC
| • | The conditions for setting the DTC are no longer present. |
| • | A history DTC clears after 100 malfunction free ignition cycles. |
| • | The BCM receives the clear code command from the scan tool. |
Diagnostic Aids
| • | The fog lamps will only illuminate under the following conditions: |
| - | The park lamps or low beam headlamps are on. |
| - | The highbeam headlamps are off. |
| - | The fog lamp switch is in the on position. |
| • | If the DTC is a history DTC, the problem may be intermittent. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Listen for an audible click when the foglamp relay operates. Command both the ON and OFF states. Repeat the commands as necessary.
-
Tests for voltage at the coil side of the foglamp relay.
-
Verifies that the body control module is providing ground to the foglamp relay.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Fog Lights Schematics | |||
1 | Did you perform the Lighting System Diagnostic System Check? | Go to Step 2 | |
Does the fog lamp relay state change with each command? | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | Go to Step 3 | |
Does the test lamp illuminate? | Go to Step 4 | Go to Step 8 | |
Does the test lamp turn ON and OFF with each command? | Go to Step 6 | Go to Step 5 | |
5 | Test the control circuit of the fog lamp relay for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 7 |
6 | Inspect for poor connections at the fog lamp relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 9 |
7 | Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 11 | Go to Step 10 |
8 | Repair the open in the coil side battery positive voltage circuit of the fog lamp relay. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 11 | -- |
9 | Replace the fog lamp relay. Did you complete the replacement? | Go to Step 11 | -- |
10 |
Important: Perform the set up procedure for the body control module. Replace the body control module. Refer to Body Control Module Replacement . Did you complete the replacement? | Go to Step 11 | -- |
11 |
Does the DTC reset? | Go to Step 2 | System OK |
