GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2004 🢒 Malibu 🢒 Vehicle Control Systems 🢒 Vehicle DTC Information 🢒 DTC B0022

Circuit Description

The passenger seat belt pretensioner deployment loop consists of an seat belt pretensioner-RF, the seat belt pretensioner-RF high and seat belt pretensioner-RF low circuits. A shorting bar used within the seat belt pretensioner connector which will short together both seat belt pretensioner high and low circuits when the connector is disconnected, this will help to prevent unwanted deployment of the pretensioner during servicing. During a frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the seat belt pretensioner. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a diagnostic trouble code (DTC) will be stored in memory.

DTC Descriptors

DTC B0022 Right Front Seat Belt Pretensioner Deployment Loop

DTC Symptom

DTC Symptom Descriptor

01

Short to battery

02

Short to ground

04

Open circuit

0D

Resistance above threshold

0E

Resistance below threshold

Conditions for Running the DTC

Ignition voltage is within the normal operating voltage range.

Conditions for Setting the DTC

B0022 01

The seat belt pretensioner-RF high and/or low circuit is short to voltage for 120 milliseconds.

B0022 02

The seat belt pretensioner-RF high and/or low circuit is short to ground for 120 milliseconds.

B0022 04

The seat belt pretensioner-RF high and/or low circuit is open for 120 milliseconds.

B0022 0D

The seat belt pretensioner-RF deployment loop resistance is more than 3.9 ohms for 120 milliseconds.

B0022 0E

The seat belt pretensioner-RF deployment loop resistance is less than 1.1 ohms for 120 milliseconds.

Action Taken When the DTC Sets

The SDM commands the AIR BAG indicator ON via GMLAN serial data.

Conditions for Clearing the MIL/DTC
    • The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
    • A history DTC will clear once 255 malfunction free ignition cycles have occurred.

Diagnostic Aids

The following are possible causes of the malfunction:

    • A short between the seat belt pretensioner-RF high and low circuits.
    • An open or a high resistance in the seat belt pretensioner-RF high or low circuits.
    • A short to ground or a short to voltage in the seat belt pretensioner-RF high or low circuits.
    • The seat belt pretensioner-RF connector
    • The SDM connector
    • A malfunctioning seat belt pretensioner
    • A malfunctioning SDM

Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction. If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. Tests to see if the malfunction is caused by the seat belt pretensioner-RF.

    2.

  2. Tests to see what DTCs are present. If DTC B0022 01 is present, test the seat belt pretensioner-RF for a short to battery voltage on the high and low circuits. If DTC B0022 02 is present, test the seat belt pretensioner-RF high and low circuits for a short to ground. If DTC B0022 04, 0D, 0E is present, test the seat belt pretensioner-RF high and low circuits for an open circuit and for high or low resistance.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

Connector End View Reference: SIR Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2
  1. Turn OFF the ignition.
  2. Disconnect seat belt pretensioner-RF in-line connector. Refer to Seat Belt Retractor Pretensioner Replacement - Front .
  3. Inspect the component and harness sides of the in-line connector for the seat belt pretensioner for damage or corrosion that may cause the malfunction. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Does the connector exhibit any signs of damage or corrosion?

Go to Step 3

Go to Step 4

3
  1. If the in-line connector for the seat belt pretensioner-RF is damaged, the seat belt pretensioner must be replaced. Refer to Seat Belt Retractor Pretensioner Replacement - Front .
  2. If the wiring harness side of the seat belt pretensioner connector is damaged, replace the harness side of the connector. Refer to Connector Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 9

--

4

  1. Connect the J 38715-A SIR Driver/Passenger Load Tool to the harness side of the seat belt pretensioner-RF connector. Use PASSENGER INFLATOR connector.
  2. Turn ON the ignition, with the engine OFF.

    3. Important: CANdi module J-45289 must be used with the scan tool.

  3. Install a scan tool, request the SIR DTC display.

Does the scan tool indicate that DTC B0022 is current?

Go to Step 5

Go to Step 7

5
  1. Turn OFF the ignition.
  2. Disconnect and remove the J 38715-A .
  3. Disconnect the inflatable restraint sensing and diagnostic module (SDM) connector. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .
  4. Inspect the SDM connector for damage or corrosion that may cause a malfunction in the seat belt pretensioner-RF high and/or low circuits. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 6

6

  1. If DTC B0022 01 is present, test the seat belt pretensioner-RF for a short to battery voltage on the high and low circuits.
  2. If DTC B0022 02 is present, test the seat belt pretensioner-RF high and low circuits for a short to ground.
  3. If DTC B0022 04, 0D, 0E is present, test the seat belt pretensioner-RF high and low circuits for an open circuit and for high or low resistance.
  4. All the above conditions refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 9

Go to Step 8

7
  1. Turn OFF the ignition.
  2. Replace the seat belt pretensioner-RF. Refer to Seat Belt Retractor Pretensioner Replacement - Front .

Did you complete the replacement?

Go to Step 9

--

8
  1. Turn OFF the ignition.
  2. Replace the SDM. Refer to Inflatable Restraint Sensing and Diagnostic Module Replacement .

Did you complete the replacement?

Go to Step 9

--

9
  1. Connect all SIR components.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK