1

Rear Compartment Lid Emblem Assembly

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from the rear compartment panel and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
4. Close the rear compartment lid prior to adhesion.
5. Using the palm of the hand, wet out the emblem to the rear compartment lid to ensure full adhesion of the emblem is made.

Special Tools

J 25070 Heat Gun - 500-750F

1

Rear Compartment Lid Emblem

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old emblem. Clean all adhesive from the rear compartment panel and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
4. Close the rear compartment lid prior to adhesion.
5. Using the palm of the hand, wet out the emblem to the rear compartment lid to ensure full adhesion of the emblem is made.

Special Tools

J 25070 Heat Gun - 500-750F

1

Rear Compartment Lid Nameplate Assembly

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from the rear compartment panel and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
4. Close the rear compartment lid prior to adhesion.
5. Using the palm of the hand, wet out the name plate to the rear compartment lid to ensure full adhesion of the name plate is made.

Special Tools

J 25070 Heat Gun - 500-750F

1

Rear Compartment Lid Emblem (LS LT LTZ)

Notice: Refer to Exterior Trim Emblem Removal Notice in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate.
3. Clean all adhesive from the rear compartment panel and wipe the surface dry with a clean lint-free towel prior to installing the new emblem.
4. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
5. Close the rear compartment lid prior to adhesion.
6. Using the palm of the hand, wet out the emblem to the rear compartment lid to ensure full adhesion of the name plate is made.

Special Tools

J 25070 Heat Gun - 500-750F