| Table 1: | Remote Control Door Lock Receiver Scan Tool Data Parameters |
| Table 2: | Remote Control Door Lock Receiver Scan Tool Output Controls |
Parameter | System State | Expected Value | Description |
|---|---|---|---|
Operating Conditions: Ignition ON | |||
Battery Voltage Signal | -- | Varies | This displays volts. This is the current battery voltage signal. |
Ext. LF Door Handle Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the exterior driver front door handle switch. |
Ext. Rear Compartment Lid Release Sw. | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the exterior rear compartment release switch. |
Ext. RF Door Handle Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the exterior passenger front door handle switch. |
Ignition Mode Switch | -- | Idle | The scan tool displays Idle, Crank or ACC/OFF. This is the state of the ignition mode switch. |
Int. LF Door Handle Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the interior driver front door handle switch. |
Int. RF Door Handle Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the interior passenger front door handle switch. |
Key Fob 1-4 Battery Signal | -- | Varies | The scan tool displays a numeric value from 1.9-3.3 or Not Present. This is the current battery signal in the corresponding key fob. |
Key Fob 1-4 Low Voltage | -- | OK | The scan tool displays OK or Low. Low is displayed if the battery in the corresponding key fob is low. |
Last Key Fob Used | -- | Varies | The scan tool displays None, Fob 1, Fob 2, Fob 3 or Fob 4. |
LF Pressure Sensor ID | -- | Varies | This displays a numeric value. This is the driver front pressure sensor identification. |
LF Pressure Sensor Mode | -- | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the driver front pressure sensor. |
LF Tire Press. Sensor Status | -- | Normal | The scan tool displays Normal or Failed. This is the status of the driver front tire pressure sensor. |
LF Tire Pressure | -- | Varies | This displays kPa (psi). This is the current pressure in the driver front tire. |
LR Pressure Sensor ID | -- | Varies | This displays a numeric value. This is the driver rear pressure sensor identification. |
LR Pressure Sensor Mode | -- | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the driver rear pressure sensor. |
LR Tire Press. Sensor Status | -- | Normal | The scan tool displays Normal or Failed. This is the status of the driver rear tire pressure sensor. |
LR Tire Pressure | -- | Varies | This displays kPa (psi). This is the current pressure in the driver rear tire. |
No. of Fobs Programmed | -- | Varies | The scan tool displays a numeric value from 0-4. |
RF Pressure Sensor ID | -- | Varies | This displays a numeric value. This is the passenger front pressure sensor identification. |
RF Pressure Sensor Mode | -- | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the passenger front pressure sensor. |
RF Tire Press. Sensor Status | -- | Normal | The scan tool displays Normal or Failed. This is the status of the passenger front tire pressure sensor. |
RF Tire Pressure | -- | Varies | This displays kPa (psi). This is the current pressure in the passenger front tire. |
RR Pressure Sensor ID | -- | Varies | This displays a numeric value. This is the passenger rear pressure sensor identification. |
RR Pressure Sensor Mode | -- | Varies | The scan tool displays Off, Re-measure, Wake, Drive, Learn or Low Batt. This is the current mode of the passenger rear pressure sensor. |
RR Tire Press. Sensor Status | -- | Normal | The scan tool displays Normal or Failed. This is the status of the passenger rear tire pressure sensor. |
RR Tire Pressure | -- | Varies | This displays kPa (psi). This is the current pressure in the passenger rear tire. |
Run/Crank Relay Command | -- | Off | The scan tool displays On or Off. This is the state of the run/crank relay command. |
Run/Crank Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the run/crank relay. |
Sensor Learn Mode | -- | Inactive | The scan tool displays Active or Inactive. Active is displayed if the tire pressure sensors are in learn mode. |
Shift Lock Solenoid Command | -- | Lock | The scan tool displays Lock or Unlock. This is the state of the shift lock solenoid command. |
Shift Lock Solenoid Command | -- | Lock | The scan tool displays Lock or Unlock. This is the state of the shift lock solenoid. |
Output Control | Description |
|---|---|
Auto. Door Unlock | This output control is used to enable or disable the automatic door unlock program into the corresponding key fob 1, 2, 3 or 4. |
Invalidate All Fobs | This output control is used to reset all key fobs for the vehicle. |
Key Fob in Veh. Warning | This output control is used to enable or disable the key fob in vehicle warning into the corresponding key fob 1, 2, 3 or 4. |
Next Available Slot | This output control is used to program the next fob into the next available slot. |
Passive Door Lock | This output control is used to enable or disable the passive door lock into the corresponding key fob 1, 2, 3 or 4. |
Program Key Fob 1-4 | This output control is used to program the corresponding key fob 1, 2, 3 or 4. |
Run/Crank Relay | This output control is used to command the run/crank relay ON or OFF. |
Setup New RCDLR | This output control is used to setup a new remote control door lock receiver (RCDLR). |
TPM Learn Mode | This output control is used to enable the tire pressure monitoring (TPM) learn mode. |
