Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC P0463: Fuel Level Sensor Circuit High VoltageDiagnostic Fault Information
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
|---|---|---|---|---|---|
Fuel Level Sensor Signal | P0462 | 1 | P0463, P0464 | P0463 | P0461 |
Fuel Level Sensor Low Reference | -- | 1 | P0463, P0464 | P0463 | P0461 |
1. Fuel Gage Inaccurate or Inoperative | |||||
Circuit/System Description
The fuel level sensor changes resistance in response to the fuel level. The engine control module (ECM) monitors the signal circuit of the fuel level sensor in order to determine the fuel level. When the fuel tank is full, the sensor resistance is low and the ECM senses a low signal voltage. When the fuel tank is empty, the sensor resistance is high and the ECM senses a high signal voltage. The ECM uses the signal circuit of the fuel level sensor in order to calculate the percentage of remaining fuel in the tank. The ECM sends the fuel level percentage via the serial data circuit to the body control module (BCM). The BCM sends the serial data message to the instrument panel cluster (IPC) in order to control the fuel gage and display the fuel level.
Conditions for Running the DTC
| • | The ignition is ON, with the engine running. |
| • | The system voltage is between 9-18 volts. |
Conditions for Setting the DTC
| • | The sensor output is greater than 2.5 volts. |
| • | The above condition is present for greater than 60 seconds. |
Action Taken When the DTC Sets
| • | The fuel gage defaults to empty. |
| • | The low fuel indicator illuminates. |
| • | The ECM records the operating conditions at the time that the diagnostic test fails. The ECM displays the failure information in the Failure Records on the scan tool. |
Conditions for Clearing the DTC
| • | The DTC becomes history when the conditions for setting the DTC are no longer present. |
| • | The history DTC clears after 40 malfunction-free warm-up cycles. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Instrument Cluster Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
Ignition ON, observe the scan tool Fuel Tank Level Remaining parameter. The reading should be between 4 percent and 98 percent.
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the fuel level sensor.
- Ignition OFF, test for less than 1 ohm between the low reference circuit terminal D and ground.
- Install a 3A fused jumper wire between the signal circuit terminal A and the low reference circuit terminal D. Verify the scan tool Fuel Tank Level Remaining parameter is greater than 98 percent.
- If all circuits test normal, perform the fuel level sensor component test before replacing fuel level sensor.
| ⇒ | If greater than the specified range, test the circuit for a short to voltage or an open/high resistance. If the circuits tests normal, replace the ECM. |
| ⇒ | If less than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM. |
Component Testing
- Ignition OFF, remove the fuel level sender.
- While sweeping the fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms of resistance between signal terminal A and the low reference terminal D.
| ⇒ | If not within the specified range, replace the fuel level sensor. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Fuel Level Sensor Replacement for the 2.4L engine |
| • | Fuel Level Sensor Replacement for the 3.5L engine |
| • | Fuel Level Sensor Replacement for the 3.6L engine |
| • | Control Module References for the ECM replacement, setup and programming |
