Circuit Description
To provide the best possible combination of driveability, fuel economy, and emission control, a closed loop air/fuel metering system is used. While in closed loop, the PCM monitors the HO2S 1 signal and adjusts fuel delivery based upon the HO2S signal voltage. A change made to fuel delivery will be indicated by the long and short term fuel trim values which can be monitored with a scan tool. Ideal fuel trim values are around 0%; if the HO2S signals are indicating a lean condition the PCM will add fuel, resulting in fuel trim values above 0%. If a rich condition is detected, the fuel trim values will be below 0%, indicating that the PCM is reducing the amount of fuel delivered. If an excessively lean condition is detected, the PCM will set DTC P0171.
The PCM's maximum authority to control long term fuel trim allows a range between -23% and +16%. The PCM's maximum authority to control short term fuel trim allows a range between -11% and +20%. The PCM monitors fuel trim under various operating conditions (fuel trim cells) before determining the status of the fuel trim diagnostic. The fuel trim cells used to determine fuel trim are as follows:
| • | Idle, purge commanded (Cell 0). |
| • | Idle, no purge commanded (Cell 0). |
| • | Normal driving, purge commanded (Cell 2). |
| • | Normal driving, no purge commanded (Cell 2). |
The vehicle may have to be operated in all of the above conditions before the PCM determines fuel trim status. The amount that fuel trim deviates from 0% in each cell and the amount that each cell is weighted directly affects whether or not the vehicle must be operated in all of the cells described above to complete the diagnostic.
Conditions for Running the DTC
| • | No MAF sensor, ECT sensor , MAP sensor, IAT sensor, HO2S sensors, TP sensor, or VSS sensor , Misfire, IAC, or fuel injector DTC(s) set. |
| • | Engine coolant temperature between 20°C (68°F) and 110°C (230°F). |
| • | Intake air temperature is between -18°C (0°F) and 70°C (158°F). |
| • | Manifold absolute pressure is between 15 kPa and 85 kPa. |
| • | Throttle angle is steady below 90%. |
| • | Vehicle speed is less than 75 mph. |
| • | Engine speed between 600 and 4000 RPM. |
Conditions for Setting the DTC
| • | Long term fuel trim is at or near maximum authority of 16%. |
| • | Short term fuel trim is at or near maximum authority of 20%. |
| • | All conditions have been met in Fuel Trim Cells 0 and 2 (purge ON / purge OFF). |
Action Taken When the DTC Sets
| • | The PCM will illuminate the MIL during the second consecutive trip in which the diagnostic test has been run and failed. |
| • | The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data. |
Conditions for Clearing the MIL/DTC
| • | The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed. |
| • | The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction. |
| • | The DTC can be cleared by using the scan tool Clear Info function or by disconnecting the PCM battery feed. |
Diagnostic Aids
Check for the following conditions:
| • | Heated oxygen sensor wiring. The sensor pigtail may be mispositioned and contacting the exhaust system. |
| • | Poor PCM to engine grounds. Refer to Engine Controls. |
| • | Fuel pressure. A condition which causes a lean exhaust can cause DTC P0171 to set. The system will go lean if pressure is too low. The PCM can compensate for some decrease. However, if fuel pressure is too low, a DTC P0137 may be set. Refer to Fuel System Pressure Test . |
| • | Lean injector(s). Perform Fuel Injector Balance Test . |
| • | Vacuum leaks. Check for disconnected or damaged vacuum hoses and for vacuum leaks at the intake manifold, throttle body, EGR system, and Crankcase Ventilation system. Refer to Emission Hose Routing Diagram . |
| • | Exhaust leaks. An exhaust leak may cause outside air to be pulled into the exhaust gas stream past the HO2S, causing the DTC P0171 to set. Check for exhaust leaks near the HO2S 1 sensor. |
| • | MAF sensor. Disconnect the MAF sensor and see if the condition is corrected. If so, replace MAF sensor. Refer to Mass Airflow Sensor Replacement . |
| • | Fuel contamination. Water, even in small amounts, can be delivered to the fuel injectors. The water can cause a lean exhaust to be indicated. Excessive alcohol in the fuel can also cause this condition. Refer to Alcohol/Contaminants-in-Fuel Test . |
| • | Poor connection at PCM. Inspect harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals, and poor terminal to wire connection |
| • | Damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, observe the HO2S 1 display on the scan tool while moving connectors and wiring harnesses related to the engine harness. A change in the display will indicate the location of the fault. |
Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.
Test Description
Number(s) below refer to the step number(s) on the Diagnostic Chart.
-
DTCs other than P0171 may indicate a condition present which may cause a lean condition. If this is the case, repairing the condition which caused the other DTC will most likely correct the DTC P0171.
-
If the DTC P0171 test passes while the Fail Records conditions are being duplicated, the lean condition is intermittent. Refer to Diagnostic Aids or Symptoms for additional information on diagnosing intermittent problems.
Step | Action | Value(s) | Yes | No | ||||
|---|---|---|---|---|---|---|---|---|
1 | Was the Powertrain On-Board Diagnostic System Check performed? | -- | ||||||
Are any DTCs set other than P0171? | -- | Diagnose applicable DTC(s) before proceeding with this diagnostic. Powertrain Control Module Diagnosis . | ||||||
3 |
Are the displayed values at or near the specified values?
| +16% +20% | ||||||
Does the scan tool indicate DTC P0171 failed this ign? | -- | Refer to Diagnostic Aids | ||||||
5 |
Was problem found? | -- | ||||||
6 |
Was problem found? | -- | ||||||
7 |
Was problem found? | -- | ||||||
8 | Start the engine and note the idle quality. Is a high or unsteady idle being experienced? | -- | ||||||
9 | With the engine idling, observe the Idle Air Control display on the scan tool. Is the displayed value greater than the specified value? (Value is displayed in counts). | 5 | ||||||
10 |
Was problem found? | -- | ||||||
11 |
Was problem found? | -- | ||||||
12 |
Was the fuel contaminated? | -- | ||||||
13 |
Was problem found? | -- | ||||||
14 |
Does Short Term FT value decrease to near the specified value? | 0% | ||||||
15 |
Was problem found? | -- | ||||||
16 |
Was problem found? | -- | ||||||
17 |
Was problem found? | -- | ||||||
18 |
Was problem found? | -- | ||||||
19 |
Was problem found? | -- | ||||||
20 |
Was problem found? | -- | Refer to Diagnostic Aids | |||||
21 | Replace the MAF sensor. Refer to Mass Airflow Sensor Replacement . Is action complete? | -- | -- | |||||
22 |
Does the scan tool indicate DTC P0171 failed this ign? | -- | System OK |
