Refer to Door Lock/Indicator Schematics .
Circuit Description
The body control module (BCM) controls the left front door lock motor. The body control module applies power to the driver's door unlock feed circuit and ground to the door lock feed circuit, which energizes the motor to unlock the door lock.
Conditions for Running the DTC
The BCM must be commanding the lock motor of the left front door to unlock the door lock.
Conditions for Setting the DTC
| • | The BCM detects a short to ground in the driver's door unlock feed circuit while trying to energize the door lock motor to unlock the door lock. |
| • | The conditions above must be present for more than 0.3 seconds. |
Action Taken When the DTC Sets
The BCM stores DTC B3127 in memory.
Conditions for Clearing the DTC
| • | A short to ground in the driver's door unlock feed circuit is no longer detected by the BCM when the BCM is commanding the left front door lock motor to unlock the door lock. |
| • | A history DTC B3127 will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present. |
| • | A scan tool may be used to clear the DTC. |
Diagnostic Aids
| • | If the DTC B3127 is a history DTC, the fault may be intermittent. Refer to Intermittents and Poor Connections. |
| • | The following conditions may cause an intermittent malfunction to occur: |
| - | An intermittent short to ground in the driver's door unlock feed circuit |
| - | The left front door lock motor is shorted to ground internally |
| - | The BCM is shorted to ground internally |
Test Description
The number(s) below refer to the step number(s) on the diagnostic table.
-
Listen for an audible noise when the left front door lock motor is commanded to unlock . Command the door lock motor to lock and unlock. Repeat the commands as necessary.
-
Verifies that the Body Control Module is providing voltage to the left front door lock motor.
-
Tests for an open in the ground circuit to the left front door lock motor.
-
Tests if voltage is constantly being applied to the left front door lock motor.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Did you perform the Diagnostic System Check for the door system? | -- | Go to Step 2 | |
Does the left front door lock motor unlock when commanded? | -- | Go to Diagnostic Aids | Go to Step 3 | |
Does the test lamp flash when the lock motor is commanded to unlock? | -- | Go to Step 4 | Go to Step 5 | |
Does the test lamp flash when commanded? | -- | Go to Step 8 | Go to Step 10 | |
Does the test lamp remain illuminated with each command? | -- | Go to Step 7 | Go to Step 6 | |
6 | Test the unlock control circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
7 | Test the unlock control circuit for a short to voltage. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 9 |
8 | Inspect for poor connections at the lock motor for the left front door. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
9 | Inspect for poor connections at the harness connector of the body control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
10 | Repair the ground circuit of the lock motor to the left front door. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 13 | -- |
11 | Replace the lock motor to the left front door. Refer to Front Side Door Lock Actuator Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- |
12 |
Did you complete the replacement? | -- | Go to Step 13 | -- |
13 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
