Power Steering Pressure Pipe/Hose Replacement L26
Removal Procedure
- Place a drain pan under the vehicle.
- Remove the accessory drive belt. Refer to
Drive Belt Replacement.
- Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle.
- Remove the tire and wheel assembly. Refer to
Tire and Wheel Removal and Installation.
- The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
- Remove the power steering pressure hose from the power steering pump.
- Remove the power steering pressure hose from the clamps on the power steering gear.
- Remove the power steering pressure hose from the vehicle.
Installation Procedure
- Install the power steering pressure hose to the vehicle.
- Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the power steering pressure hose to the power steering pump.
Tighten
Tighten the fitting to 27 N·m (20 lb ft).
- Install the power steering pressure hose to the power steering gear.
Tighten
Tighten the pressure hose fitting to 27 N·m (20 lb ft).
- Install the tire and wheel assembly. Refer to
Tire and Wheel Removal and Installation.
- Remove the drain pan from under the vehicle.
- Lower the vehicle.
- Install the accessory drive belt. Refer to
Drive Belt Replacement.
- Fill the power steering system with power steering fluid. Refer to
Checking and Adding Power Steering Fluid.
- Bleed the power steering system. Refer to
Power Steering System Bleeding.
- Inspect the power steering system for leaks. Refer to
Power Steering Fluid Leaks.
Power Steering Pressure Pipe/Hose Replacement 3.4L
Removal Procedure
- Place a drain pan under the vehicle.
- Remove the power steering
pressure line from the power steering pump.
- Remove the power steering pressure line from the power steering
lines retaining bracket on the engine.
- The power steering pressure
line is the lower line at the power steering gear.
Remove the
power steering line from the power steering gear . Access the line from
the engine compartment, between the rocker arm cover and the front of the
dash mat.
- Raise and suitably support the vehicle. Refer to
Lifting and Jacking the Vehicle
in General Information.
- Remove the power steering
pressure line (1) from the clamps on the power steering gear.
- Remove the power steering pressure line (1) from the vehicle.
Installation Procedure
- Install the power steering
pressure line (1) to the vehicle.
- Install the power steering pressure line (1) to the clamps
on the power steering gear.
- Lower the vehicle.
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the power steering pressure line to the power steering gear.
Tighten
Tighten the power steering pressure line fitting to the power steering
gear to 27 N·m (20 lb ft).
- Install the power steering pressure line to the power steering
lines retaining bracket on the engine.
- Install the power steering
pressure line to the power steering pump.
Tighten
Tighten the power steering pressure line fitting to the power steering
pump to 27 N·m (20 lb ft).
- Fill the power steering system with power steering fluid. Refer
to
Checking and Adding Power Steering Fluid
.
- Bleed the power steering system. Refer to
Power Steering System Bleeding
.
- Inspect the power steering system for leaks. Refer to
Power Steering Fluid Leaks
.