Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement Impala

1. Open the hood.
2. Remove the radiator air baffle. Refer to Radiator Air Upper Baffle and Deflector Replacement in Engine Cooling.
3. Apply light pressure to the headlamp lens to hold the headlamp in place while removing the retainers.
4. Lift up the headlamp retainers to release the headlamp from the upper fascia support.
5. Remove the headlamp from the slots in the upper fascia support.



6. Disconnect the electrical connector from the headlamp.
7. Remove the headlamp from the vehicle.



8. Remove the rubber access cover from the headlamp.




Caution: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

•	Turn off the lamp switch and allow the bulb to cool before changing the bulb.

•	Leave the lamp switch OFF until the bulb change is complete.

•	Always wear eye protection when changing a halogen bulb.

•	Handle the bulb only by its base. Avoid touching the glass.

•	Keep dirt and moisture off the bulb.

•	Properly dispose of the used bulb.

•	Keep halogen bulbs out of the reach of children.

9. Remove the bulb/socket from the headlamp by rotating counterclockwise.



10. Disconnect the electrical connector from the bulb/socket.

1. Connect the electrical connector to the bulb/socket.



2. Install the bulb/socket to the headlamp by rotating clockwise.



3. Install the rubber access cover to the headlamp.



4. Connect the electrical connector to the headlamp.



5. Position the headlamp to the upper fascia support.
6. Push the headlamp retainers down until fully seated.
7. Install the radiator air baffle. Refer to Radiator Air Upper Baffle and Deflector Replacement in Engine Cooling.
8. Check and adjust the headlamp aim as necessary. Refer to Headlamp Aiming .
9. Close the hood.

Headlamp Assembly or Headlamp Bulb and/or Cornering, Sidemarker, Park, Turn Signal Bulb Replacement Monte Carlo

1. Open the hood.
2. Remove the radiator air baffle. Refer to Radiator Air Upper Baffle and Deflector Replacement in Engine Cooling.
3. Apply light pressure to the headlamp lens to hold the headlamp in place while removing the retainers.
4. Lift up the headlamp retainers to release the headlamp from the upper fascia support.
5. Remove the headlamp from the slots in the upper fascia support.



6. Disconnect the electrical connector from the headlamp.
7. Remove the headlamp from the vehicle.



8. Remove the rubber access cover from the headlamp.




Caution: Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:

•	Turn off the lamp switch and allow the bulb to cool before changing the bulb.

•	Leave the lamp switch OFF until the bulb change is complete.

•	Always wear eye protection when changing a halogen bulb.

•	Handle the bulb only by its base. Avoid touching the glass.

•	Keep dirt and moisture off the bulb.

•	Properly dispose of the used bulb.

•	Keep halogen bulbs out of the reach of children.

9. Remove the bulb/socket from the headlamp by rotating counterclockwise.



10. Disconnect the electrical connector from the bulb/socket.

1. Connect the electrical connector to the bulb/socket.



2. Install the bulb/socket to the headlamp by rotating clockwise.



3. Install the rubber access cover to the headlamp.



4. Connect the electrical connector to the headlamp.



5. Position the headlamp to the upper fascia support.
6. Push the headlamp retainers down until fully seated.
7. Install the radiator air baffle. Refer to Radiator Air Upper Baffle and Deflector Replacement in Engine Cooling.
8. Check and adjust the headlamp aim as necessary. Refer to Headlamp Aiming .
9. Close the hood.