Hydraulic Clutch Hose/Pipe Replacement LHD

1. Disable the SIR system. Refer to SIR Disabling and Enabling .

Caution: Refer to Battery Disconnect Caution in the Preface section.

2. Disconnect the battery ground cable from the battery. Refer to Battery Negative Cable Disconnection and Connection .

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.





Important: Do not fully remove the hydraulic clutch hose/pipe retaining clip (3) from the clutch master cylinder (2).

3. Release the hydraulic clutch hose/pipe retaining clip (3) from the clutch master cylinder (2).
4. Disconnect the hydraulic clutch hose/pipe (1) from the clutch master cylinder (2).

Caution: Refer to Safety Glasses Caution in the Preface section.

Caution: Refer to Vehicle Lifting Caution in the Preface section.

5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .
6. Remove the transmission assembly. Refer to Transmission Replacement .




Important: The hydraulic clutch hose/pipe (2) is located at the top of the bulk head.

7. Detach the clutch hose/pipe (2) securing clip (1), from the bulk head by squeezing both clip tangs together.
8. Remove the hydraulic clutch hose/pipe (2).

1. Install the hydraulic clutch hose/pipe (2).

Important: The hydraulic clutch hose/pipe (2) is located at the top of the bulk head.

2. Attach the hydraulic clutch hose/pipe securing clip (1), to the bulk head, ensuring that both retaining tangs are correctly engaged in the body.
3. Install the transmission assembly. Refer to Transmission Replacement .
4. Lower the vehicle.




Important: Listen for an audible click to confirm fitting.

Important: Inspect clutch pipe seals for any damage, replace pipe if seals are damaged.

5. Connect the hydraulic clutch hose/pipe (1) to the clutch master cylinder (2).
6. Bleed the clutch hydraulic system. Refer to Hydraulic Clutch Bleeding .
7. Enable the SIR system. Refer to SIR Disabling and Enabling .
8. Connect the battery ground cable to the battery. Refer to Battery Negative Cable Disconnection and Connection .
9. Road test vehicle for correct clutch operation.

Hydraulic Clutch Hose/Pipe Replacement LHD

1. Disable the SIR system. Refer to SIR Disabling and Enabling.

Caution: Refer to Battery Disconnect Caution in the Preface section.

2. Disconnect the battery ground cable from the battery. Refer to Battery Negative Cable Disconnection and Connection.

Caution: Refer to Brake Fluid Irritant Caution in the Preface section.

Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.





Important: Do not fully remove the hydraulic clutch hose/pipe retaining clip (3) from the clutch master cylinder (2).

3. Release the hydraulic clutch hose/pipe retaining clip (3) from the clutch master cylinder (2).
4. Disconnect the hydraulic clutch hose/pipe (1) from the clutch master cylinder (2).

Caution: Refer to Safety Glasses Caution in the Preface section.

Caution: Refer to Vehicle Lifting Caution in the Preface section.

5. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle.
6. Remove the transmission assembly. Refer to Transmission Replacement.




Important: The hydraulic clutch hose/pipe (2) is located at the top of the bulk head.

7. Detach the clutch hose/pipe (2) securing clip (1), from the bulk head by squeezing both clip tangs together.
8. Remove the hydraulic clutch hose/pipe (2).

1. Install the hydraulic clutch hose/pipe (2).

Important: The hydraulic clutch hose/pipe (2) is located at the top of the bulk head.

2. Attach the hydraulic clutch hose/pipe securing clip (1), to the bulk head, ensuring that both retaining tangs are correctly engaged in the body.
3. Install the transmission assembly. Refer to Transmission Replacement.
4. Lower the vehicle.




Important: Listen for an audible click to confirm fitting.

Important: Inspect clutch pipe seals for any damage, replace pipe if seals are damaged.

5. Connect the hydraulic clutch hose/pipe (1) to the clutch master cylinder (2).
6. Bleed the clutch hydraulic system. Refer to Hydraulic Clutch Bleeding.
7. Enable the SIR system. Refer to SIR Disabling and Enabling.
8. Connect the battery ground cable to the battery. Refer to Battery Negative Cable Disconnection and Connection.
9. Road test vehicle for correct clutch operation.