DTC P0462 w/Delphi Controller
Circuit Description
The fuel level sensor changes resistance based on fuel level. The fuel level sensor has a signal circuit and a ground circuit. The engine control module (ECM) applies 5 volts on the signal circuit to the sensor. The ECM monitors the changes in this voltage caused by changes in the resistance of the sensor in order to determine fuel level.
When the fuel tank is full, the sensor resistance is low, and the ECM signal voltage is high. When the fuel tank is empty, the sensor resistance is high, and the signal voltage is low.
The ECM uses inputs from the fuel level sensor in order to calculate the total fuel percentage remaining in the fuel tank. The ECM uses the fuel level information for the evaporative emission (EVAP) and misfire diagnostics. The fuel level information is sent to the instrument panel cluster (IPC).
If the ECM detects a signal voltage lower than the operating range of the sensor, this DTC sets.
DTC Descriptors
This diagnostic procedure supports the following DTC:
DTC P0462 Fuel Level Sensor Circuit Low Voltage
Conditions for Running the DTC
| • | The engine is running. |
| • | DTC P0462 runs continuously once the above conditions are met. |
Conditions for Setting the DTC
| • | The ECM detects that fuel level signal voltage is less than 0.25 volts. |
| • | The above condition is present for more than 10 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame/Failure Records. |
| • | The fuel gage defaults to empty. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Use the Freeze Frame and/or Failure Records data in order to locate an intermittent condition. If you cannot duplicate the DTC, the information included in the Freeze Frame and/or Failure Records data may aid in determining the number of miles since the DTC set. The Fail Counter and Pass Counter can also aid in determining the number of ignition cycles that the diagnostic reported a pass and/or fail. Operate the vehicle within the same freeze frame conditions (RPM, engine load, vehicle speed, temperature, etc.). This will isolate when the DTC failed. |
| • | Intermittent Conditions in Engine Controls - 1.4L DOHC |
| • | Intermittent Conditions in Engine Controls - 1.6L (L91) |
| • | Intermittent Conditions in Engine Controls - 1.8L (L79) |
| • | Intermittent Conditions in Engine Controls - 2.0L (L34) |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Value | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views | ||||||||||||
1 | Did you perform the Diagnostic System Check - Instrument Cluster? | -- | Go to Step 2 | |||||||||
Is the voltage more than the specified value? | 4.25 V | Go to Step 4 | Go to Step 3 | |||||||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids | ||||||||
4 |
Is the voltage less than the specified value? | 4.25 V | Go to Step 6 | Go to Step 5 | ||||||||
5 | Test the signal circuit of the fuel level sender for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 7 | ||||||||
6 | Test for shorted terminals and poor connections at the fuel level sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 8 | ||||||||
7 | Test for shorted terminals and poor connections at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 10 | Go to Step 9 | ||||||||
8 | Replace the fuel sender assembly. Refer to one of the following:
Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
9 | Replace the control module. Refer to one of the following:
Did you complete the replacement? | -- | Go to Step 10 | -- | ||||||||
10 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 11 | ||||||||
11 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- |
| System OK | ||||||||
DTC P0462 wo/Delphi Controller
Circuit Description
The fuel level sensor changes resistance based on the amount of fuel in the fuel tank. The fuel level sensor has a common, or shared 5-volt reference circuit and a signal circuit. The engine control module (ECM) applies 5.0 volts on the reference circuit to the sensor. The ECM monitors the changes in this voltage on the signal circuit, caused by a change in the resistance of the fuel level sensor, in order to determine fuel level. The fuel level sensor is part of the fuel sender, and is serviced as an assembly.
When the fuel tank is full, the sensor resistance is low, and the ECM signal voltage is high. When the fuel tank is empty, the sensor resistance is high, and the signal voltage is low.
The ECM uses inputs from the fuel level sensor in order to calculate the total fuel percentage remaining in the fuel tank. The ECM uses the fuel level information for the EVAP and misfire diagnostics. The fuel level information is sent to the instrument panel cluster (IPC).
If the ECM detects a signal voltage lower than the operating range of the sensor, this DTC sets.
DTC Descriptors
This diagnostic procedure supports the following DTC:
DTC P0462 Fuel Level Sensor Circuit Low Voltage
Conditions for Running the DTC
| • | The engine is operating. |
| • | DTC P0462 runs continuously once the above conditions are met. |
Conditions for Setting the DTC
| • | The ECM detects that fuel level signal voltage is less than 0.20 volts. |
| • | The above condition is present for more than 10 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
| • | The fuel gage defaults to empty. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Test Description
The number below refers to the step number on the diagnostic table.
-
This step verifies that a condition exists.
-
This step tests for a condition in the 5-volt reference circuit of the fuel level sensor. If the DMM does not display more than the specified voltage, test for a short to ground or an open in the 5-volt reference circuit.
-
This step tests for a condition in the signal circuit of the fuel level sensor. If the Fuel Level Voltage parameter does not display more than the specified voltage, test for a short to ground or an open in the signal circuit.
Step | Action | Value | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Instrument Cluster Schematics Connector End View Reference: Instrument Panel, Gages, and Console Connector End Views | ||||||||||||
1 | Did you perform the Diagnostic System Check - in Instrument Cluster? | -- | Go to Step 2 | |||||||||
Is the voltage less than the specified value? | 0.2 V | Go to Step 4 | Go to Step 3 | |||||||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids | ||||||||
Is the voltage more than the specified value? | 4.8 V | Go to Step 5 | Go to Step 7 | |||||||||
Is the voltage less than the specified value? | 4.8 V | Go to Step 6 | Go to Step 8 | |||||||||
6 | Test the signal circuit of the fuel level sensor for one of the following conditions:
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 | ||||||||
7 | Test the 5-volt reference circuit of the fuel level sensor and all shared 5-volt reference circuits for one of the following conditions:
Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 | ||||||||
8 | Test for an intermittent and for a poor connection at the fuel sender assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 | ||||||||
9 | Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 | ||||||||
10 | Replace the fuel sender assembly. Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||||
11 | Replace the ECM. Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||||
12 |
Did the DTC fail this ignition? | -- | Go to Step 2 | System OK | ||||||||
