Tools Required

Caution: Refer to Battery Disconnect Caution in the Preface section.




1. Disconnect the negative battery cable.
2. Move the gear select lever to the Park position.
3. Remove the battery. Refer to Battery and Battery Tray Replacement in Engine Electrical.
4. Install J 28467-B  (1).



5. Disconnect the transaxle wiring harness from the transaxle.
6. Disconnect the electrical connector from the park/neutral position (PNP) switch.



7. Remove the clips from the shift control cable and disconnect the cable from the transaxle.



8. Remove the bolts that secure the upper transaxle to the engine.



9. Remove the left transaxle mounting bracket. Refer to Transmission Mount Bracket Replacement .

Notice: Refer to Vehicle Lifting and Jacking Notice in the Preface section.




10. Raise and suitable support the vehicle.
11. Drain the transaxle fluid.
12. Remove the oil cooler pipes from the transaxle. Refer to Transmission Fluid Cooler Hose/Pipe Replacement .



13. Remove the drive axle. Refer to Front Drive Axle Inner Shaft Replacement in Front Drive Axle.
14. Remove the starter motor. Refer to Starter Motor Replacement in Engine Electrical.
15. Remove the rubber access cover from the transaxle, then remove the flywheel to torque converter bolts.



16. Support the transaxle.
17. Remove the bolts (1) from the rear transaxle mounting bracket.
18. Remove the bolt and nut (2) from the damping block connection.



19. Use DW 260-010  (1) to support the transaxle assembly.



20. Remove the bolts that retain the lower engine to the transaxle.



21. Using the DW 260-010  (1), remove the transaxle assembly.

Important: After installing the transmission assembly, the shift adapts must be reset. reset the shift adapts using the scan tool. Go to "Trans Adaptives Reset" under "Special Functions" on the scan tool.




1. Install the transaxle assembly into the vehicle.
2. Use the DW 260-010  (1) to support the transaxle assembly.

Notice: Refer to Fastener Notice in the Preface section.




3. Install the bolts (1, 2, 3) that retain the lower engine to the transaxle.

Tighten

•	Tighten bolt (1) to 75 N·m (55 lb ft).

•	Tighten bolt (2) to 21 N·m (15 lb ft).

•	Tighten bolt (3) to 31 N·m (23 lb ft).




4. Install the bolts (1) to the rear transaxle mounting bracket.

Tighten
Tighten bolt to 62 N·m (45 lb ft).

5. Install the bolt and nut (2) to the damping block connection.

Tighten
Tighten bolt to 68 N·m (50 lb ft).

6. Install the flywheel to torque converter bolts.

Tighten
Tighten the converter to flywheel bolts to 45 N·m (33 lb ft).

7. Install the rubber access cover on the transaxle assembly.
8. Install the starter motor. Refer to Starter Motor Replacement in Engine Electrical.
9. Install the drive axle. Refer to Front Drive Axle Inner Shaft Replacement in Front Drive Axle.



10. Install the oil cooler pipes to the transaxle. Refer to Transmission Fluid Cooler Hose/Pipe Replacement .
11. Lower the vehicle.



12. Install the left transaxle mounting bracket. Refer to Transmission Mount Bracket Replacement .



13. Install the bolts that secure the upper transaxle to the engine.

Tighten
Tighten the bolts to 75 N·m (55 lb ft).




14. Install the clips to the shift control cable. Connect the cable.



15. Install the PNP switch electrical connector.
16. Connect the transaxle wiring harness to the transaxle.



17. Remove J 28467-B  (1).
18. Install the battery. Refer to Battery and Battery Tray Replacement in Engine Electrical.
19. Add transaxle fluid. Refer to Transmission Fluid Level Inspection .
20. Connect the negative battery cable.

Important: After installing the transmission assembly, the shift adapts must be reset. reset the shift adapts using the scan tool. Go to "Trans Adaptives Reset" under "Special Functions" on the scan tool.