GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2005 🢒 Optra 🢒 Transmission/Transaxle 🢒 Automatic Transmission - ZF 4HP 16 🢒 DTC P1874

DTC P1874 Non-Europe or N. American Emissions

Circuit Description

The pressure control valves 3,4,5 and 6 are precision electronic pressure regulators that control the operation of the clutches, brakes and lock-up clutch.

The valve reduces the system pressure with which the downstream solenoid valves and electrical pressure regulating valves are supplied. It is possible to use smaller solenoid valves as a result. The pressure control solenoid valves require a constant input pressure.

Conditions for Setting the DTC
    •  No DTC P1871.
    •  Immediately after the above condition occurs.

Action Taken When the DTC Sets
    •  The hold lamp will blink.
    •  The transmission control module (TCM) will record operating conditions at the time the diagnostic fails. This information will be stored in the Failure Records buffer.
    •  Adopt Emergency/ Substitute mode and constant 4th gear.
    •  Power supply cut off to the pressure control solenoid valve.

Conditions for Clearing the Hold Lamp/DTC
    •  The hold lamp will turn OFF when the malfunction has not occurred after three-ignition cycle.
    •  A history DTC will clear after 40 consecutive warm up cycles without a fault.
    •  Using a scan tool can clear history DTCs.

Diagnostic Aids

When DTC P1874 sets, the possible cause of the fault could be the solenoid valve power supply line.

DTC P1874

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Automatic Transmission

2
  1. Install the scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. Start the engine and allow the engine to warm up at idle.
  4. Put the gear selector in Park and set the parking brake.
  5. Observe "solenoid 1,2" on the scan tool.

Is the solenoid ON?

--

Go to Diagnostic Aids

Go to Step 3

3
  1. Turn the ignition OFF.
  2. Disconnect the transaxle wiring connector and the TCM connector.
  3. Measure the voltage of the transaxle wiring terminal 3.

Is the voltage within the specified value?

11-14V

Go to Step 4

Go to Step 5

4

Repair the circuit for a short to power.

Is the action complete?

--

System OK

--

5
  1. Remove the oil pan.
  2. Disconnect the solenoid 1,2 wiring connector.
  3. Turn the ignition ON, with the engine OFF.
  4. Measure the voltage of the solenoid 1 terminal 2.
  5. Measure the voltage of the solenoid 2 terminal 2.

Is the voltage within the specified value?

11-14V

Go to Step 6

Go to Step 7

6

Repair the circuits for a short to power.

Is the action complete?

--

System OK

--

7

Replace the TCM. Refer to Transmission Control Module Replacement .

Is the action complete?

--

Go to Step 8

--

8
  1. After the repair, use a scan tool "clear info" function and road test the vehicle.
  2. Review the "DTC info".

Has the last test failed or is the current DTC displayed?

--

Go to Step 2

System OK

DTC P1874 European and N. American Emissions

Circuit Description

The pressure control valves 3,4,5 and 6 are precision electronic pressure regulators that control the operation of the clutches, brakes and lock-up clutch.

The valve reduces the system pressure with which the downstream solenoid valves and electrical pressure regulating valves are supplied. It is possible to use smaller solenoid valves as a result. The pressure control solenoid valves require a constant input pressure.

Conditions for Setting the DTC
    •  No DTC P1871.
    •  Immediately after the above condition occurs.

Action Taken When the DTC Sets
    • The malfunction indicator lamp (MIL) will illuminate.
    •  The transmission control module (TCM) will record operating conditions at the time the diagnostic fails. This information will be stored in the Failure Records buffer.
    •  Adopt Emergency/ Substitute mode and constant 4th gear.
    •  Power supply cut off to the pressure control solenoid valve.

Conditions for Clearing the MIL/DTC
    •  The MIL will turn OFF when the malfunction has not occurred after three-ignition cycle.
    •  A history DTC will clear after 40 consecutive warm up cycles without a fault.
    •  Using a scan tool can clear history DTCs.

Diagnostic Aids

When DTC P1874 sets, the possible cause of the fault could be the solenoid valve power supply line.

DTC P1874

Step

Action

Values

Yes

No

1

Did you perform the Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Automatic Transmission

2
  1. Install the scan tool.
  2. Turn the ignition ON, with the engine OFF.
  3. Start the engine and allow the engine to warm up at idle.
  4. Put the gear selector in Park and set the parking brake.
  5. Observe "solenoid 1,2" on the scan tool.

Is the solenoid ON?

--

Go to Diagnostic Aids

Go to Step 3

3
  1. Turn the ignition OFF.
  2. Disconnect the transaxle wiring connector and the TCM connector.
  3. Measure the voltage of the transaxle wiring terminal 3.

Is the voltage within the specified value?

11-14V

Go to Step 4

Go to Step 5

4

Repair the circuit for a short to power.

Is the action complete?

--

System OK

--

5
  1. Remove the oil pan.
  2. Disconnect the solenoid 1,2 wiring connector.
  3. Turn the ignition ON, with the engine OFF.
  4. Measure the voltage of the solenoid 1 terminal 2.
  5. Measure the voltage of the solenoid 2 terminal 2.

Is the voltage within the specified value?

11-14V

Go to Step 6

Go to Step 7

6

Repair the circuits for a short to power.

Is the action complete?

--

System OK

--

7

Replace the TCM. Refer to Transmission Control Module Replacement .

Is the action complete?

--

Go to Step 8

--

8
  1. After the repair, use a scan tool "clear info" function and road test the vehicle.
  2. Review the "DTC info".

Has the last test failed or is the current DTC displayed?

--

Go to Step 2

System OK