Diagnostic Instructions

DTC Descriptors

DTC P0122: Throttle Position (TP) Sensor Circuit Low Voltage

DTC P0123: Throttle Position (TP) Sensor Circuit High Voltage

DTC P0222:  Idle Speed Control (ISC) Motor Position Sensor Circuit Low Voltage

DTC P0223:  Idle Speed Control (ISC) Motor Position Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	High Resistance	Open	Short to Voltage	Signal Performance
5-Volt Reference	P0122, P0222	P0510, P2119	P0122, P0222	P0123, P0223	--
Idle Motor Position Signal	P0222	P2118	P0222	P0223	--
Idle Motor Switch Signal	P0510	--	P0510	--	--
Throttle Position Sensor Signal	P0122	P0510	P0122	P0123	--
Idle Motor High Control	P2101, P2118	P2101, P2118	P2101, P2118	P2101, P2118	--
Idle Motor Low Control	P2101, P2118	P2101, P2118	P2101, P2118	--	--
Low Reference	--	--	P0123, P0223	--	--

Typical Scan Tool Data

ISC Motor Position Sensor

Circuit	Short to Ground	Open	Short to Voltage
Operating Conditions: Engine operating in Closed Loop. Parameter Normal Range: ISC Motor Position Sensor 5%/3.66 Volts
5-Volt Reference	0%/0.0 Volts	0%/0.0 Volts	0%/5.0 Volts
ISC Motor Position Signal	0%/0.0 Volts	0%/0.0 Volts	0%/5.0 Volts
Low Reference	--	0 %/5.0 Volts	--

TP Sensor

Circuit	Short to Ground	Open	Short to Voltage
Operating Conditions: The engine is operating in Closed Loop. Parameter Normal Range: TP Position Sensor 5%/4.2 Volts
5-Volt Reference	6%/0.4 Volts	6%/0.0 Volts	14%/5.0 Volts
Throttle Position Sensor Signal	6%/0.0 Volts	6%/0.0 Volts	6%/5.0 Volts
Low Reference	--	6%/5.0 Volts	--

Circuit/System Description

The throttle body assembly uses an idle speed control (ISC) system that contains a motor, throttle position (TP) sensor, motor position sensor, and an idle switch. The ISC system is used to control engine speed at idle. The engine control module (ECM) uses a high and low control circuit to control the ISC motor. A 5-volt reference and low reference supplied by the ECM is shared by both the TP and ISC motor position sensors. The TP and ISC motor position sensors each have a signal circuit to feedback voltage to the ECM. The ECM commands the ISC motor by pulse width modulating the voltage on the high and low control circuits to adjust the throttle angle for idle speed control. The motor position sensor is used by the ECM to monitor the position of the ISC motor for idle operation. The TP sensor is used by the ECM to monitor the position of the throttle blade. An idle switch is used by the ECM to monitor when the throttle blade is at it rest position to allow the ISC motor to control idle operation. With the throttle blade at the rest position, the idle switch will be closed. When the throttle blade is opened, the idle switch will be open.

The ISC system consist of the following circuits:

Conditions for Running the DTC

Conditions for Setting the DTC

P0122

The ECM detects that the TP sensor voltage is less than 0.3 volt.

P0123

The ECM detects that the TP sensor voltage is greater than 4.9 volts.

P0222

The ECM detects that the ISC motor position sensor voltage is less than 0.257 volt.

P0223

The ECM detects that the ISC motor position sensor voltage is greater than 4.9 volts.

Action Taken When the DTC Sets

Conditions for Clearing the DTC

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Circuit/System Verification

1. Start the engine. Observe the TP Sensor or the ISC Motor Position Sensor parameters with a scan tool. The parameters should be between 0.4-4.5 volts.
2. If the vehicle passes the Circuit/System Verification Test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector of the throttle body assembly.
2. Ignition ON, verify that the TP sensor/ISC motor position sensor voltage parameter is less than 0.3 volt.

⇒	If greater than 0.3 volt, test the signal circuit of the TP sensor/ISC motor position sensor for a short to voltage. If the circuit/connections test normal, replace the ECM.

Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit of the TP sensor/ISC motor position sensor and ground.

⇒	If less than 4.8 volts, test the 5-volt reference circuit of the TP sensor/ISC motor position sensor for a short to ground or open/high resistance. If the circuit/connections test normal, replace the ECM.

⇒	If greater than 5.2 volts, test the 5-volt reference circuit of the TP sensor/ISC motor position sensor for a short to voltage. If the circuit/connections test normal, replace the ECM.

4. Ignition ON, test for less than 0.2 volt between the low reference circuit of the TP sensor/ISC motor position sensor and a good ground.

⇒	If greater than 0.2 volt, test the low reference circuit of the TP sensor/ISC motor position sensor for a short to voltage. If the circuit/connections test normal, replace the ECM.

5. Ignition OFF, test for less than 5 ohms of resistance between the low reference circuit of the TP sensor/ISC motor position sensor and ground.

⇒	If greater than 5 ohms, test the low reference circuit of the TP sensor/ISC motor position sensor for an open/high resistance. If the circuit/connections test normal, replace the ECM.

6. Ignition ON, install a 3-amp fused jumper wire between the appropriate signal circuit and the 5-volt reference circuit of the TP sensor/ISC motor position sensor to verify that the TP sensor/ISC motor position sensor voltage parameter is greater than 4.8 volts.

⇒	If less than 4.8 volts, test the appropriate signal circuit of the TP sensor/ISC motor position sensor for a short to ground or an open/high resistance. If the circuit/connections test normal, replace the ECM.

7. If all circuits/connections test normal, test or replace the throttle body assembly.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.