DTC C0110 North America
Circuit Description
When the electronic brake control module (EBCM) grounds the pump motor relay, it closes and provides battery voltage to the pump motor if the valve relay is closed. The EBCM senses the voltage applied to the pump motor to verify motor operation.
This DTC sets when the EBCM detects B+ without motor relay activation or if the EBCM does not detect B+ after motor relay activation.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC C0110 Pump Motor Circuit
Conditions for Running the DTC
| • | Vehicle speed is greater than 6 km/h (4 mph) with the brake pedal not applied |
| or |
| • | Vehicle speed is greater than 15 km/h (9 mph) and the brake pedal is actuated. |
Conditions for Setting the DTC
| • | There is a faulty terminal in the pump motor connector. |
| • | There is a faulty terminal in the EBCM connector. |
| • | There is a problem in the antilock brake system (ABS) wiring harness. |
| • | There is high resistance in the chassis ground. |
| • | The EBCM is defective. |
| • | There is a problem in the wiring from the pump motor connector to the motor. |
Action Taken When the DTC Sets
The antilock brake system (ABS) is disabled, and the ABS warning lamp is ON. The electronic brake force distribution (EBD) is disabled.
Conditions for Clearing the DTC
The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
Diagnostic Aids
It is very important to perform a thorough inspection of the wiring and the connectors. Failure to do so may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step checks for connector damage.
-
This step checks for a poor ground connection.
-
This step checks for a possible problem with the motor connector at the ABS unit.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Component Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
Is the terminal damaged or corroded? | -- | Go to Step 3 | Go to Step 4 | |
3 | Repair or replace the terminal, the connector, the wiring harness, or the EBCM as required. Did you complete the action? | -- | Go to Step 11 | -- |
Measure the resistance from terminal 26 of the harness connector to a good chassis ground. Is the resistance equal to the specified value? | 0 ohms | Go to Step 8 | Go to Step 5 | |
5 | Measure the resistance at the chassis ground connection G106. Is the resistance equal to the specified value? | 0 ohms | Go to Step 7 | Go to Step 6 |
6 | Repair the connection at chassis ground G106. Did you complete the repair? | -- | Go to Step 11 | -- |
7 | Repair the open or the high resistance in the harness between terminal 26 of connector J1 and the ground lug, or replace the antilock brake system (ABS) wiring harness. Did you complete the action? | -- | Go to Step 11 | -- |
Is there any sign of damage or corrosion that would prevent a good ground contact? | -- | Go to Step 9 | Go to Step 10 | |
9 | Repair or replace the defective terminal, connector, or EBCM as required. Did you complete the action? | -- | Go to Step 11 | -- |
10 | Replace the EBCM. Did you complete the replacement? | -- | Go to Step 11 | -- |
11 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
DTC C0110 Except North America
Circuit Description
When the electronic brake control module (EBCM) grounds the pump motor relay, it closes and provides battery voltage to the pump motor if the valve relay is closed. The EBCM senses the voltage applied to the pump motor to verify motor operation.
This DTC sets when the EBCM detects B+ without motor relay activation or if the EBCM does not detect B+ after motor relay activation.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC C0110 Pump Motor Circuit
Conditions for Running the DTC
| • | Vehicle speed is greater than 6 km/h (4 mph) with the brake pedal not applied |
| or |
| • | Vehicle speed is greater than 15 km/h (9 mph) and the brake pedal is actuated. |
Conditions for Setting the DTC
| • | There is a faulty terminal in the pump motor connector. |
| • | There is a faulty terminal in the EBCM connector. |
| • | There is a problem in the antilock brake system (ABS) wiring harness. |
| • | There is high resistance in the chassis ground. |
| • | The EBCM is defective. |
| • | There is a problem in the wiring from the pump motor connector to the motor. |
Action Taken When the DTC Sets
The antilock brake system (ABS) is disabled, and the ABS warning lamp is ON. The electronic brake force distribution (EBD) is disabled.
Conditions for Clearing the DTC
The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
Diagnostic Aids
It is very important to perform a thorough inspection of the wiring and the connectors. Failure to do so may result in misdiagnosis, causing part replacement with reappearance of the malfunction.
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step checks for connector damage.
-
This step checks for a poor ground connection.
-
This step checks for a possible problem with the motor connector at the ABS unit.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Antilock Brake System Schematics Connector End View Reference: Component Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | |
Is the terminal damaged or corroded? | -- | Go to Step 3 | Go to Step 4 | |
3 | Repair or replace the terminal, the connector, the wiring harness, or the EBCM as required. Did you complete the action? | -- | Go to Step 11 | -- |
Measure the resistance from terminal 47 of the harness connector to a good chassis ground. Is the resistance equal to the specified value? | 0 ohms | Go to Step 8 | Go to Step 5 | |
5 | Measure the resistance at the chassis ground connection G106. Is the resistance equal to the specified value? | 0 ohms | Go to Step 7 | Go to Step 6 |
6 | Repair the connection at chassis ground G106. Did you complete the repair? | -- | Go to Step 11 | -- |
7 | Repair the open or the high resistance in the harness between terminal 47 of connector J1 and the ground lug, or replace the antilock brake system (ABS) wiring harness. Did you complete the action? | -- | Go to Step 11 | -- |
Is there any sign of damage or corrosion that would prevent a good ground contact? | -- | Go to Step 9 | Go to Step 10 | |
9 | Repair or replace the defective terminal, connector, or EBCM as required. Did you complete the action? | -- | Go to Step 11 | -- |
10 | Replace the EBCM. Did you complete the replacement? | -- | Go to Step 11 | -- |
11 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
