Diagnostic Instructions
DTC Descriptor
DTC P0327: Knock Sensor (KS) Circuit Low Frequency
Circuit/System Description
The knock sensor (KS) enables the engine control module (ECM) to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation. The KS produces an AC voltage signal that varies
depending on the vibration level during engine operation. The ECM adjusts the spark timing based on the amplitude and the frequency of the KS signal. The ECM receives the KS signal through a signal circuit. The ECM supples a ground circuit to the KS through
a low reference circuit. The ECM also supplies a shielded ground circuit to the KS. The ECM learns a KS noise level at idle and uses calibrated values for the rest of the engine speed range. The ECM should monitor a normal KS signal within the noise channel.
The circuits between the KS sensor and the ECM consist of the following circuits:
Conditions for Running the DTC
| • | DTCs P0107 and P0108 are not set. |
| • | The engine coolant temperature (ECT) is more than 50°C (122°F). |
| • | The engine speed is more than 1,600 RPM. |
| • | The manifold absolute pressure (MAP) is between 10-50 kPa. |
| • | DTC P0327 runs continuously once the above conditions are met. |
Conditions for Setting the DTC
The ECM detects an incorrect KS signal for more than 4 seconds.
Action Taken When the DTC Sets
DTC P0327 is a Type B DTC.
Conditions for Clearing the DTC
DTC P0327 is a Type B DTC.
Diagnostic Aids
The following conditions could also set this DTC:
| • | Inspect the KS for physical damage. A KS that is dropped or damaged may cause a DTC to set. |
| • | Inspect the KS for proper installation. A KS that is loose or over torqued may cause a DTC to set. The KS should be free of thread sealant. The KS mounting surface should be free of burrs, casting flash, and foreign material. |
| • | The KS must be clear of hoses, brackets, and engine electrical wiring. |
| • | An electromagnetic interference (EMI) condition on the shielded ground circuit |
Reference Information
Schematic Reference
Engine Controls Schematics
Connector End View Reference
Description and Operation:
Knock Sensor (KS) System Description
Electrical Information Reference
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Circuit/System Verification
- Start the engine, observe the DTC information with a scan tool. DTC P0327 should not set.
- If the vehicle passes the Circuit/System Verification Test, then operate the vehicle within the conditions for running the DTC. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.
Circuit/System Testing
Important: If the knock sensor lead is damaged in any way, replace the knock sensor.
- Ignition OFF, disconnect the harness connector of the knock (KS) sensor.
- Ignition ON, connect a test lamp between the signal circuit of the KS and the negative battery terminal.
| ⇒ | If the test lamp illuminates, test the signal circuit for a short to voltage. If the circuits/connections test normal, replace the ECM. |
- Ignition ON, connect a test lamp between the signal circuit of the KS and the positive battery terminal.
| ⇒ | If the test lamp illuminates, test the signal circuit for a short to ground. If the circuits/connections test normal, replace the ECM. |
- Ignition OFF, connect a DMM between the signal circuit and the low reference circuit.
- Test for 90-110 K ohms between the signal circuit and the low reference circuit of the KS.
| ⇒ | If the resistance is not within the specified range, test the circuits for an open/high resistance. If the circuits/connections test normal, replace the ECM. |
- If all circuits/connections test normal, replace the KS sensor.
Repair Instructions
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
