GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

    Warning: Refer to Battery Disconnect Warning in the Preface section.


    Object Number: 1289763  Size: SH
  1. Disconnect the negative battery cable.
  2. Disconnect the intake air temperature (IAT) sensor connector.
  3. Remove the air cleaner outlet hose from the throttle body.
  4. Remove the breather tube from the camshaft cover.

  5. Object Number: 1289768  Size: SH
  6. Remove the air cleaner housing bolts.
  7. Remove the air cleaner housing.
  8. Remove the right front wheel. Refer to Tire and Wheel Removal and Installation.
  9. Remove the right front wheel well splash shield. Refer to Wheelhouse Splash Shield Replacement.

  10. Object Number: 1289772  Size: SH
  11. Remove the serpentine accessory drive belt. Refer to Power Steering Pump Belt Replacement.
  12. Remove the crankshaft pulley bolts.
  13. Remove the crankshaft pulley.
  14. Remove the right engine mount bracket. Refer to Engine Mount Replacement.

  15. Object Number: 1289773  Size: SH
  16. Remove the front timing belt cover bolts.
  17. Remove the front timing belt cover.

  18. Object Number: 1289785  Size: SH
  19. Rotate the crankshaft at least one full turn clockwise using the crankshaft gear bolt.
  20. Align the mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.

Adjustment Procedure


    Object Number: 1289784  Size: SH
  1. Align the camshaft gear timing marks. Use the exhaust gear mark (2) for the exhaust gear and the intake gear mark (1) for the intake gear, since the gear are interchangeable.

  2. Object Number: 1289788  Size: SH
  3. Loosen the automatic tensioner bolt. To relieve the belt tension, turn the hex-key tab counterclockwise.
  4. Rotate the automatic tensioner hex-key tab clock wise until the adjust arm pointer of the timing belt automatic tensioner is aligned with the notch in the timing belt automatic tensioner bracket.

  5. Object Number: 1289785  Size: SH
  6. Tighten the automatic tensioner bolt.
  7. Rotate the crankshaft two full turns clockwise using the crankshaft gear bolt.
  8. Check the automatic tensioner pointer.
  9. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1289788  Size: SH
  10. When the adjust arm pointer of the timing belt automatic tensioner is aligned with the notch on the timing belt automatic tensioner bracket, the belt is tensioned correctly.
  11. Tighten
    Tighten the automatic tensioner bolt to 25 N·m (18 lb ft).

Installation Procedure


    Object Number: 1289773  Size: SH
  1. Install the front timing belt cover.
  2. Caution: Refer to Fastener Caution in the Preface section.

  3. Install the front timing belt cover bolts.
  4. Tighten
    Tighten the front timing belt cover bolts to 6 N·m (53 lb in).


    Object Number: 1289772  Size: SH
  5. Install the crankshaft pulley.
  6. Install the crankshaft pulley bolt.
  7. Tighten
    Tighten the crankshaft pulley bolt to 20 N·m (15 lb ft).

  8. Install the right engine mount bracket. Refer to Engine Mount Replacement.
  9. Install the serpentine accessory drive belt. Refer to Power Steering Pump Belt Replacement.

  10. Object Number: 1289763  Size: SH
  11. Install the right front wheel well splash shield. Refer to Wheelhouse Splash Shield Replacement.
  12. Install the right front wheel. Refer to Tire and Wheel Removal and Installation.
  13. Install the air cleaner housing.
  14. Install the air cleaner housing bolts.
  15. Tighten
    Tighten the air cleaner housing bolts to 10 N·m (89 lb in).

  16. Connect the air cleaner outlet hose to the throttle body.

  17. Object Number: 1289768  Size: SH
  18. Connect the breather tube to the camshaft cover.
  19. Connect the IAT sensor connector.
  20. Connect the negative battery cable.