Tools Required

Important: This test should only be performed at a normal operating fluid temperature of 50-80°C (122-176°F).

1. Raise the vehicle. Support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
2. Remove 6 bolts and left splash shield from vehicle.
3. Remove the left splash shield.



4. Remove the pressure tap bolt (2) from the rear of the transaxle.



5. Install J 35752 into the line pressure tap at the rear of the transaxle.
6. Install J 21867 into J 35752 .
7. Lower the vehicle.
8. Route J 21867 hose over the front fender and through the driver's window so that it can be read from the passenger compartment.
9. Connect the scan tool to the Data Link Connector (DLC) and display the engine RPM.
10. Apply the parking brake and block the vehicle wheels.
11. Press the brake pedal fully and start the engine.
12. Display engine speed (RPM) on the scan tool.

Caution: For the following four steps, procedures for testing line pressure at idle and stall speeds, the brake pedal must be fully pressed throughout the measurement procedure. Failure to do so could result in personal injury and/or property damage.

13. Place the manual selector in the drive (D) range and record the line pressure at idle speed (650-750 RPM).

Notice: DO NOT run engine at stall speed for more than five seconds continuously or engine oil and transaxle fluid temperatures may become excessively high.

14. Press the accelerator pedal fully/wide open throttle and record the line pressure in the drive (D) range at stall speed (2,150-2,450 RPM). Release the accelerator pedal.
15. Keeping the brake pedal fully pressed, place the selector lever in the reverse (R) range and record the line pressure at idle speed (650-750 RPM).
16. Press the accelerator pedal fully/wide open throttle and record the line pressure in the reverse (R) range at stall speed (2,150-2,450 RPM). Release the accelerator pedal.
17. Keep brake pedal fully pressed.
18. Place manual selector in Low range. Record line pressure at idle speed (650-750 RPM).
19. Press accelerator pedal fully/wide open throttle and record line pressure in Low range at stall speed (2,150-2,450 RPM). Release accelerator pedal.
20. Keeping brake pedal fully pressed, place manual selector in Reverse range and record line pressure at idle speed (650-750 RPM).
21. Press accelerator pedal fully/wide open throttle and record line pressure in Reverse range at stall speed (2,150-2,450 RPM). Release accelerator pedal.
22. Place manual selector in Park range and turn ignition switch to LOCK.
23. Remove the scan tool from the vehicle.
24. Remove J 21867 from the passenger compartment.
25. Raise the vehicle. Support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
26. Remove J 21867 from J 35752 .
27. Remove J 35752 from the line pressure tap at the rear of the transaxle.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

28. Install the line pressure tap bolt into the line pressure tap at the rear of the transaxle.

Tighten
Tighten the line pressure tap bolt to 9 N·m (80 lb in).

29. Install the left splash shield.
30. Secure with 6 bolts.

Tighten
Tighten the splash shield bolts to 5 N·m (44 lb in).

31. Lower the vehicle.

Compare the line pressure test results with the Line Pressure Results in the following table. If the line pressure is not as specified, refer to the Line Pressure Test Diagnosis for further evaluation.