GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 1998 🢒 S10 Pickup - 2WD 🢒 Engine 🢒 Engine Mechanical - 2.2L 🢒 Intake Manifold Replacement

Removal Procedure

    Object Number: 346145 Size: SH
  1. Disconnect the battery negative cable. Refer to Battery Replacement in Engine Electrical.
  2. Remove the upper fan shroud. Refer to Fan Shroud Replacement in Engine Cooling.
  3. Disconnect the vacuum brake booster hose.
  4. Remove the air cleaner outlet resonator. Refer to Air Cleaner Outlet Resonator Replacement in Engine Controls.

    5. Object Number: 175505 Size: SH
  5. Remove the EGR valve inlet pipe from the EGR valve adapter and the intake manifold.

    6. Object Number: 5659 Size: SH
  6. Disconnect the following electrical connectors:
    7. • Idle air control (IAC) motor
    • Manifold absolute pressure (MAP) sensor
    • Throttle position (TP) sensor
    • Fuel injector harness connector.

    Object Number: 349637 Size: SH
  7. Disconnect the vacuum hoses from the throttle body.

    8. If necessary, mark the hoses in their original locations to ensure they are properly re-connected.


    Object Number: 303008 Size: SH
  8. Remove the right fender wheelhouse extension.

    9. Object Number: 354625 Size: SH
  9. Remove the following retainers from the intake manifold:
    10. • Engine harness bracket
    • Transmission fluid level indicator tube, if equipped
    • Fuel system evaporator pipe

    Object Number: 199002 Size: SH
  10. Disconnect the fuel pipes from the fuel rail. Refer to Fuel Hose/Pipes Assembly Replacement in Engine Controls.
  11. Remove the accelerator control cable from the throttle body. Refer to Accelerator Control Cable Replacement in Engine Controls.
  12. Remove the cruise control cable from the throttle body. Refer to Cruise Control Cable Replacement (2.2L) in Cruise Control.

    13. Object Number: 382647 Size: SH
  13. Remove the spark plug wires from the spark plugs. Refer to Spark Plug Wire Harness Replacement in Engine Electrical.
  14. Remove the spark plug wire harness retainer from the heater hose pipe and set aside the spark plug wire harness.

    15. Object Number: 43037 Size: SH
  15. Working through the wheelhouse, remove the generator rear brace from the engine.
    16. • Remove the nuts holding the brace to the intake stud and the engine block.
    • Remove the bolt holding the brace to the rear of the generator.

    Object Number: 349613 Size: SH
  16. Remove the engine wiring harness bracket at the back of the engine using the following procedure:
    17. 16.1. Loosen the bolt at the rear of the cylinder head.
    16.2. Remove the two bolts that secure the bracket to the valve rocker arm cover.
    16.3. Slide the bracket off of the bolt at the rear of the cylinder head.

    Object Number: 182948 Size: SH
  17. Remove the intake manifold assembly. Refer to Intake Manifold Removal .
  18. Clean all sealing surfaces. Refer to Intake Manifold Cleaning and Inspection .

Installation Procedure

    Object Number: 182948 Size: SH
  1. Install the intake manifold assembly. Refer to Intake Manifold Installation .

    2. Object Number: 349613 Size: SH
  2. Install the engine wiring harness bracket to the rear of the engine using the following procedure:
    3. 2.1. Slide the bracket over the bolt at the rear of the cylinder head.

    Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    2.2. Install the two bolts that secure the bracket to the valve rocker arm cover.
  3. Tighten the bolts in the following order:

    4. Tighten

    1. Tighten the two bolts to the valve rocker arm cover to 10 N·m (88 lb in).
    2. Tighten the bolt at the rear of the cylinder head to 25 N·m (18 lb ft).

    Object Number: 43037 Size: SH
  4. Working through the wheelhouse, install the generator rear brace.
  5. Install the nuts holding the brace to the intake manifold stud and the stud on the engine.
  6. Install the bolt holding the brace to the rear of the generator.

    7. Tighten
    Tighten the generator rear brace nuts and bolts to 25 N·m (18 lb ft).


    Object Number: 382647 Size: SH
  7. Position the spark plug wire harness.
  8. Install the spark plug wire harness retainer on the heater hose pipe.
  9. Install the spark plug wires to the spark plugs. Refer to Spark Plug Wire Harness Replacement in Engine Electrical.
  10. Install the accelerator control cable to the throttle body. Refer to Air Cleaner Outlet Resonator Replacement in Engine Controls.
  11. Install the cruise control cable to the throttle body. Refer to Cruise Control Cable Replacement (2.2L) in Cruise Control.
  12. Connect the fuel pipes to the fuel rail. Refer to Fuel Hose/Pipes Assembly Replacement in Engine Controls.

    13. Object Number: 354625 Size: SH
  13. Install the following retainers:
    14. • Engine harness bracket
    • Transmission fluid level indicator tube, if equipped
    • Fuel system evaporator pipe

    Object Number: 349637 Size: SH
  14. Connect the vacuum hoses to the throttle body in their original locations.

    15. Object Number: 5659 Size: SH
  15. Connect the following electrical connectors:
    16. • Idle air control (IAC) motor
    • Manifold absolute pressure (MAP) sensor
    • Throttle position (TP) sensor
    • Fuel injector harness connector.

    Object Number: 175505 Size: SH
  16. Install the EGR valve inlet pipe to the EGR adapter and the intake manifold using new gaskets.

    17. Tighten

        • Tighten the EGR valve inlet pipe to the EGR adapter bolts to 25 N·m (18 lb ft).
        • Tighten the EGR valve inlet pipe to the intake manifold bolts to 10 N·m (88 lb in).

    Object Number: 303008 Size: SH
  17. Install the right fender wheelhouse extension.
  18. Install the air cleaner outlet resonator. Refer to Air Cleaner Outlet Resonator Replacement in Engine Controls.

    19. Object Number: 346145 Size: SH
  19. Install the upper fan shroud. Refer to Fan Shroud Replacement in Engine Cooling.
  20. Connect the vacuum brake booster hose.
  21. Connect the battery negative cable. Refer to Battery Replacement in Engine Electrical.