GM Service Manual Online
For 1990-2009 cars only

Parking Brake Rear Cable Replacement RWD Pickups

Tools Required

J 37043 Park Brake Cable Release Tool

Removal Procedure


    Object Number: 795856  Size: SH
  1. Release the park brake, if applied.
  2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Loosen the adjuster nut at the equalizer.

  4. Object Number: 795848  Size: SH
  5. Remove the rear park brake cable from the park brake connector.

  6. Object Number: 109  Size: SH
  7. Remove the rear park brake cable adjuster from the equalizer.

  8. Object Number: 159798  Size: SH
  9. Remove the brake drum. Refer to Brake Drum Replacement in Drum Brakes.

  10. Object Number: 793099  Size: SH
  11. Remove the rear brake shoes. Refer to Brake Shoe Replacement in Drum Brakes.

  12. Object Number: 328483  Size: SH
  13. Disconnect the rear park brake cables from the chassis and rear axle housing retainers.

  14. Object Number: 795729  Size: SH
  15. Disconnect the rear park brake cable from the park brake level, left side shown.
  16. Collapse the park brake cable locking finger at the backing plate.
  17. Remove the park brake cable from the backing plate.
  18. Remove the rear park brake cable from the vehicle.

Installation Procedure


    Object Number: 328483  Size: SH

    Important: When routing the cables through the guide loop, route the left side cable first.

  1. Install the park brake cable in the chassis and rear axle housing retainers.

  2. Object Number: 795729  Size: SH

    Important: When performing the following service procedure, ensure that the locking fingers for the park brake cable are fully seated against the backing plate.

  3. Install the rear park brake cable in the backing plate.
  4. Install the park brake cable in the park brake level.

  5. Object Number: 793099  Size: SH
  6. Install the rear brake shoes. Refer to Refer to Brake Shoe Replacement in Drum Brakes.
  7. Install the park brake cable to the equalizer.

  8. Object Number: 795848  Size: SH
  9. Install the park brake cable in the park brake cable connector.

  10. Object Number: 159798  Size: SH
  11. Install the rear brake drums. Refer to Brake Drum Replacement in Drum Brakes.

  12. Object Number: 794054  Size: SH
  13. Using a screwdriver (1), adjust the rear brake shoes (2). Refer to Drum Brake Adjustment in Drum Brakes.
  14. Adjust the park brakes. Refer to Park Brake Adjustment .
  15. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Parking Brake Rear Cable Replacement S4WD Pickups and Utilities

Removal Procedure

Tools Required

J 37043 Park Brake Cable Release Tool


    Object Number: 795856  Size: SH
  1. Release the park brake, if applied.
  2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Loosen the front cable at the equalizer.

  4. Object Number: 794051  Size: SH
  5. Using theJ 37043 (1), collapse the locking finger for the rear park brake cable.

  6. Object Number: 795848  Size: SH
  7. Remove the rear park brake cable from the connector.
  8. Remove the rear park brake cable from the equalizer.

  9. Object Number: 794043  Size: SH
  10. Using the J 37043 (1), collapse the locking finger for the rear park brake cable.
  11. Slide the inner park brake cable to the rearward.

  12. Object Number: 592331  Size: SH
  13. Remove the park brake cable from the frame retainers.

  14. Object Number: 328483  Size: SH
  15. Remove the park brake cable from the rear axle housing retainers, if needed.

  16. Object Number: 820907  Size: SH
  17. Remove the park brake cable from the park brake actuator.
  18. Using the J 37043 (1), collapse the locking tabs on the park brake cable.

  19. Object Number: 820905  Size: SH
  20. Remove the J 37043 (1) from the park brake cable.

  21. Object Number: 820904  Size: SH
  22. Remove the park brake cable from the rear brake cable bracket.

Installation Procedure

Important: When installing the park brake cable in any of the retainers, ensure that the locking tabs on the park brake cable are fully seated against the retainer.


    Object Number: 592331  Size: SH
  1. Install the park brake cable frame retainers.

  2. Object Number: 328483  Size: SH
  3. Install the park brake cable in the rear axle housing retainers, if removed.

  4. Object Number: 820904  Size: SH
  5. Install the park brake cable in the brake caliper bracket.
  6. Install the park brake cable on the park brake actuator.

  7. Object Number: 109  Size: SH
  8. Install the park brake cable on the equalizer

  9. Object Number: 795848  Size: SH
  10. Install the park brake cable in the connector.
  11. Adjust the park brake. Refer to Park Brake Adjustment
  12. Lower the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.