The fuel system is controlled by the control module located
in the engine compartment. The control module is the control center of the
system.
The basic function of the fuel system is to control the fuel delivery
to the engine under all of the operating conditions. The following
two types of fuel injection systems deliver the fuel to the engine:
The main control sensor is the (Heated) Oxygen Sensor (HO2S). The (H)O2S
is located in the exhaust manifold. The (H)O2S tells the control module the
amount of oxygen in the exhaust gas. The control module changes the air to
fuel ratio to the engine by controlling the fuel injector. Efficient catalytic
converter operation requires a 14.7:1 air to fuel ratio. Because the constant
measuring and adjusting of the air to fuel ratio, the fuel injection system
is called a Closed Loop system.
These parameters determine the mode of engine operation.
The following is a list of the 2 types of fuel systems with the various
applications :
The control module monitors the voltages from several sensors in order
to determine how much fuel to give the engine. The fuel is delivered under
one of several conditions called modes. The control module controls all of
the modes.
When the key is first turned ON, the control module turns on the fuel
pump relay for 2 seconds, and the fuel pump builds up pressure to the throttle
body. The control module checks the Engine Coolant Temperature (ECT) sensor,
the Intake Air Temperature (IAT) sensor, the Throttle Position (TP) sensor,
the Manifold Absolute Pressure (MAP) sensor, and the ignition signal. The
control module determines the proper air to fuel ratio for starting. This
ranges from 1.5:1 at -36°C (-33°F) to 14.6:1, at 94°C
(201°F) running temperature.
If the engine floods, clear the engine by depressing the accelerator
pedal down to the floor. The control module then pulses the injector at a
16.5:1 air to fuel ratio. The control module holds this injector rate as long
as the throttle stays wide open and the engine is below 600 RPM. If
the throttle position becomes less than 65 percent, the control module returns
to the starting mode.
The run mode is the mode under which the engine operates most of the
time. In this mode, the engine operates in either Open Loop or Closed Loop.
When the engine is first started and it is above 400 RPM, the
system goes into the Open Loop operation. In the Open Loop, the control module
ignores the signal from the HO2S, and the control module calculates the air
to fuel ratio based on the inputs from the Engine Coolant Temperature (ECT)
sensor and the Manifold Absolute Pressure (MAP) sensor.
A normal functioning system may go into an Open Loop at idle if the
Heated Oxygen Sensor (HO2S) temperature drops below the minimum requirement
to produce the voltage fluctuation.
The specific values for the above conditions vary with different engines.
The Electronically Erasable Programmable Read Only Memory (EEPROM) stores
the values. When these conditions are met, the systems goes into a Closed
Loop operation. In a Closed Loop, the control module calculates the air to
fuel ratio (injector on-time) based on the signal from the HO2S. This allows
the air to fuel ratio to stay very close to 14.6:1.
When the control module senses rapid changes in the throttle position
and the manifold pressure, the system enters the acceleration mode. The system
provides the extra fuel needed for smooth acceleration.
When deceleration occurs, the fuel remaining in the intake manifold
can cause excessive emissions and backfiring. When the control module observes
a fast reduction in the throttle opening and a sharp decrease in the manifold
pressure, the control module causes the system to enter the deceleration mode
by reducing the amount of fuel delivered to the engine. When deceleration
is very fast, the control module cuts OFF the fuel completely for short lengths
of time.
This mode comes into operation at highway speeds. The purpose of the
mode is to improve the fuel economy. For the control module to operate in
this mode, the control module first must sense the correct engine coolant
temperature, ignition control, canister purge activity, and constant engine
speed. During the semi-Closed-Loop operation, there will exist the following
items will exist:
Upon deceleration, the control module senses a high MAP vacuum (low
voltage or kPa) to command a leaner air/fuel mixture in order to reduce emissions.
Note that the control module can trigger this condition (decel en-leanment)
while the vehicle is not moving.
The PCM can misdiagnose the Decel-En-leanment mode of operation as a
lean condition. The control module runs the system lean on decel, or if the
MAP sensor senses a low voltage (high engine vacuum), with the vehicle standing
still, the control module leans out the fuel delivery.
If the technician notes, while testing a control module system (with
a scan tool) with the transmission in P, that the HO2S reading is low (usually
below 100 mV), the long term and short term fuel trims are both around
128 counts, lower the engine speed to 1000 RPM.
If the oxygen sensor and the long term fuel trim numbers respond normally
at this RPM, this may indicate that the system was fooled into the decel en-leanment
mode of operation. If the heated oxygen sensor and the long term fuel trim
numbers do not respond at the lower RPM readings, other problems exist with
the vehicle.
When the battery voltage is low, the control module can compensate for
a weak spark delivered to the distributor by increasing the following items:
No fuel is delivered by the injector when the ignition is OFF. This
prevents dieseling. Also, the fuel is not delivered if no reference pulses
are seen from the Ignition system, which means the engine is not running.
The fuel cutoff also occurs during high engine RPM. In order to protect the
internal engine components from damage, the control module disables the fuel
when the vehicle speed reaches a specified speed.
