Engine Mechanical Specifications. Chevrolet S10 Pickup

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1998 🢒 S10 Pickup - 4WD 🢒 Engine 🢒 Engine Mechanical - 2.2L 🢒 Engine Mechanical Specifications

Application	Specifications
Application	Metric	English
General Data
Engine Type	--	L-4
Displacement	--	2.2L (134 CID)
RPO (Engine VIN Code)	--	LN2 (4)
Bore	89 mm	3.5 in
Stroke	88 mm	3.46 in
Compression Ratio	--	8.85:1
Firing Order	--	1-3-4-2
Oil Pressure @ 65°C (150°F)	348 kpa	56 psi @ 3000 RPM
Cylinder Bore
Diameter	88.991-89.009 mm	3.5036-3.5043 in
Out Of Round Maximum	0.013 mm	0.0005 in
Taper -- Thrust Side Maximum	0.013 mm	0.0005 in
Cylinder Head
Cylinder Head Deck Face Overall Maximum Flatness	0.08 mm	0.003 in
Cylinder Head Deck Face Maximum Flatness within any 150 mm (5.92 in) length	0.05 mm	0.002 in
Cylinder Head Deck Face Maximum Flatness within 25 mm (0.984 in) length	0.025 mm	0.001 in
Lubrication System
Oil Capacity Without Filter Change	3.473 L	3.5 qts
When Changing the Oil Filter, Up to an Additional 0.473 Liter or One Half Quart of Oil May Be Needed. Filter Type or Equivalent	PF-47
Oil Pressure (3000 RPM @ 65°C (150°F)	348 kPa	56 psi min.
Piston
Clearance	0.015-0.047 mm	0.0006-0.0018 in
Piston Ring Compression
Top Groove Side Clearance	0.05-0.027 mm	0.0019-0.0011 in
Second Groove Side Clearance	0.05-0.027 mm	0.0019-0.0011 in
Top Ring Gap	0.25-0.50 mm	0.010-0.020 in
Second RIng Gap	0.25-0.50 mm	0.010-0.020 in
Piston Ring Oil
Groove Clearance	0.05-0.021 mm	0.0019-0.0082 in
Gap	0.25-1.27 mm	0.010-0.050 in
Piston Pin
Diameter	20.320-20.325 mm	0.8000-0.8002 in
Clearance In Piston	0.008-0.0016 mm	0.0003-0.0006 in
Interference Fit In Rod	0.025-0.045 mm	0.00098-0.0017 in
Oil Pump
Outer Gerotor Thickness	17.087-17.099 mm	0.6727-0.6731 in
Oil Pump Drive to Driven Gear Backlash	0.23-0.51 mm	0.0091-0.0201 in
Valve to Bore Clearance	0.038-0.089 mm	0.0015-0.0035 in
Gear Lash	0.094-0.195 mm	0.004-0.008 in
Gear Pocket Depth	30.36-30.44 mm	1.195-1.198 in
Gear Pocket Diameter	38.18-38.25 mm	1.503-1.506 in
Gear Length (Drive Gear)	30.45-30.48 mm	1.199-1.20 in
Gear Length (Idler)	30.45-30.48 mm	1.199-1.20 in
Gear Diameter (Drive Gear)	38.05-38.10 mm	1.498-1.50 in
Gear Diameter (Idler)	38.05-38.10 mm	1.498-1.5 in
Gear Side Clearance (Drive Gear)	0.038-0.102 mm	0.001-0.004 in
Gear Side Clearance (Idler)	0.038-0.102 mm	0.001-0.004 in
End Clearance	0.05-0.18 mm	0.002-0.007 in
Crankshaft
Main Journal Diameter	63.360-63.384 mm	2.4945-2.4954 in
Main Journal Taper	0.005 mm	0.00019 in
Main Journal Out Of Round	0.005 mm	0.00019 in
Main Bearing Clearance	0.015-0.047 mm	0.0006-0.0019 in
Crankshaft End Play	0.0511-0.1780 mm	0.002-0.007 in
Rod Bearing Journal Diameter	50.758-50.784 mm	1.9983-1.9994 in
Rod Bearing Journal Taper	0.005 mm	0.00019 in
Rod Bearing Journal Out Of Round	0.005 mm	0.00019 in
Rod Bearing Journal Clearance	0.025-0.079 mm	0.00098-0.0031 in
Rod Side Clearance	0.10-0.38 mm	0.0039-0.0149 in
Camshaft
Lobe Lift (Inlet and Exhaust)	6.685 mm	0.263 in
Journal Diameter	47.453-47.478 mm	1.868-1.869 in
Journal Clearance	0.013-0.089 mm	0.0005-0.0035 in
Valve System
Rocker Arm Ratio	--	1.6
Valve Face Angle	--	45°
Valve Face Runout	0.038 mm	0.0014 in
Valve Margin (Exhaust)	2.13-1.87 mm	0.083-0.073 in
Valve Margin (Inlet)	1.49-1.23 mm	0.058-0.048 in
Valve Head Diameter (Inlet)	37 mm	1.45 in
Valve Head Diameter (Exhaust)	44 mm	1.73 in
Valve Overall Length (Inlet)	134.23 mm	5.28 in
Valve Overall Length (Exhaust)	127 mm	5.00 in
Valve Stem to Guide Clearance (Inlet)	0.020-0.053 mm	0.0007-0.0020 in
Valve Stem to Guide Clearance (Exhaust)	0.035-0.076 mm	0.0014-0.0029 in
Valve Guide Inside Diameter	7.000-7.020 mm	0.275-0.276 in
Valve Tip to Retainer Groove Centerline	4.97-5.46 mm	0.195-0.214 in
Valve Springs Free Length	48.7 mm	1.91 in
Valve Seat Width (Inlet)	2.80 mm	0.110 in
Valve Seat Width (Exhaust)	3.51 mm	0.138 in
Valve Springs Load (Closed)	361-324 N·m @ 40.64 mm	81.2-72.8 lb @ 1.600 in
Valve Springs Load (Open)	957-893 N·m @ 29.85 mm	215-201 lb @ 1.175 in