Notice: If the engine is damaged internally and a new engine assembly is installed in the vehicle, ensure that all foreign material is flushed out of the cooling system. You must also flush out the oil cooler system. Failure to rid the oil cooler system of debris can result in engine damage.

Tool Required

J 41427 Engine Lift Bracket

1. Disconnect the battery negative cable. Refer to Battery Replacement in Engine Electrical.
2. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
3. Remove the underbody shields.
4. Remove the braces from the engine to the transmission (manual transmission only). Refer to Transmission Replacement in Manual Transmission - New Venture.
5. Remove the exhaust pipe from the exhaust manifolds. Refer to Exhaust Manifold Pipe Replacement in Engine Exhaust.
6. Disconnect the oil cooler pipes (RWD vehicle). Refer to Engine Oil Cooler Hose/Pipe Replacement in Engine Cooling.
7. Disconnect the remote oil filter adapter inlet and outlet hoses (Four Wheel Drive vehicle). Refer to Remote Oil Filter Adapter Pipe Replacement .



8. Remove the bolt holding the starter wire harness and if equipped, transmission cooler lines.
9. Remove the starter. Refer to Starter Motor Replacement in Engine Electrical.



10. Remove the transmission cover.
11. Disconnect the front propeller shaft (Four Wheel Drive only). Refer to Front Propeller Shaft Replacement in Propeller Shaft.
12. Remove the transfer case, if equipped.

•	Refer to Transfer Case Replacement (With Automatic Transmission) in Transfer Case - NVG 236 (Two Speed Automatic).

•	Refer to Transfer Case Replacement in Transfer Case - NVG 136-NP4 (One Speed Automatic).




13. Remove the rear engine mount to crossmember nut.
14. Remove the crossmember.
15. In order to remove the top transmission bolts lower the rear of the transmission after removing the crossmember.
16. Remove the transmission.

•	Refer to Transmission Replacement in Automatic Transmission - 4L60-E.

•	Refer to Transmission Replacement in Manual Transmission - New Venture.




17. Remove the front engine mount through bolts.
18. Lower the vehicle.



19. Remove the PCV tube from the right valve rocker arm cover and the air cleaner outlet duct.
20. Remove the air cleaner outlet duct from the throttle body.
21. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls.
22. Remove the radiator. Refer to Radiator Replacement in Engine Cooling.
23. Remove the inlet and outlet radiator hoses from the engine. Refer to Radiator Hose Replacement in Engine Cooling.
24. Disconnect the heater hoses from the engine. Refer to Heater Hoses Replacement in Heating and Ventilation (Non A/C).



25. Disconnect the following electrical connectors:

•	The fuel meter body assembly

•	The EVAP canister purge solenoid valve

•	The idle air control (IAC) motor

•	The throttle position (TP) sensor

•	The A/C compressor high pressure switch, if equipped

•	The A/C clutch switch, if equipped

•	The exhaust gas recirculation (EGR) valve

•	The engine coolant temperature (ECT ) sensor

•	The ignition control module (ICM)

•	The generator

•	The crankcase position (CKP) sensor

26. Release the engine wiring harness retainers and move the wiring harness aside.



27. Remove the battery ground cable at the engine.



28. Remove the bolts holding the ground wires to the left cylinder head.
29. Remove the bolt holding the fuel pipe bracket to the rear of left cylinder head.



30. Remove the bolts holding the ground wires to the right cylinder head.

Caution: In order to avoid possible injury or vehicle damage, always replace the accelerator control cable with a NEW cable whenever you remove the engine from the vehicle.

In order to avoid cruise control cable damage, position the cable out of the way while you remove or install the engine. Do not pry or lean against the cruise control cable and do not kink the cable. You must replace a damaged cable.
31. Remove the accelerator cable from the throttle shaft and the accelerator cable bracket. Refer to Accelerator Control Cable Replacement in Engine Controls.
32. Remove the cruise control cable, if equipped from the throttle shaft and the accelerator cable bracket. Refer to Cruise Control Cable Replacement in Cruise Control.



33. Remove the accelerator control cable bracket from the throttle body.
34. Remove the water pump pulley. Refer to Water Pump Replacement in Engine Cooling.
35. Remove the A/C compressor, if equipped. Refer to Air Conditioning Compressor Replacement in HVAC Systems with A/C - Manual.



36. Remove the nuts holding the power steering pump rear bracket to the engine.



37. Remove the power steering pump mounting bracket.

•	The power steering pump can remain on the mounting bracket.

•	The hoses do not require removal.

•	Remove the three bolts and the nut.

•	Slide the power steering pump mounting bracket off of the stud.

•	Secure the power steering pump mounting bracket out of the way.

38. Remove the distributor cap. Refer to Distributor Replacement in Engine Electrical.
39. Disconnect the fuel pipes. Refer to Fuel Hose/Pipes Replacement - Engine Compartment in Engine Controls.
40. Disconnect the EVAP canister purge solenoid valve pipe.



41. Disconnect the vacuum brake booster line from the intake manifold.
42. Remove the water outlet. Refer to Engine Coolant Thermostat Replacement in Engine Cooling.



43. Remove the EGR valve inlet pipe from the intake and the exhaust manifolds.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

44. Attach the J 41427 to the left front and the right rear intake manifold mounting bolts, using the following procedure:

44.1.

Remove the right rear lower intake manifold bolts.

44.2.

Install the J 41427 marked RIGHT REAR.

44.3.

Install the retaining bolts.

44.4.

Remove the left front lower intake manifold bolts.

44.5.

Install the J 41427 marked LEFT FRONT with the arrow pointing to the front of the engine.

44.6.

Install the retaining bolts.

Tighten
Tighten the retaining bolts to 15 N·m (11 lb ft).

45. Attach a suitable lifting device to the engine lift brackets.
46. Remove the engine.

Notice: If the engine is damaged internally and a new engine assembly is installed in the vehicle, ensure that all foreign material is flushed out of the cooling system. You must also flush out the oil cooler system. Failure to rid the oil cooler system of debris can result in engine damage.

Tool Required

J 41427 Engine Lift Bracket

1. Install the engine into the vehicle.




Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the engine mount through-bolts and nuts.

Tighten
Tighten the engine mount through-bolts or the nuts to the following:

•	Tighten the through-bolts to 74 N·m (55 lb ft)

•	Tighten the nuts to 63 N·m (46 lb ft)

3. Remove the J 41427 and the engine lifting device.
4. Apply thread lock GM PN 12345382 or equivalent to the threads of the lower intake manifold bolts.
5. Install the intake manifold bolts.

Tighten

1. Tighten the bolts the first pass to 3 N·m (27 lb in).
2. Tighten the bolts the first pass to 12 N·m (106 lb in).
3. Tighten the bolts the first pass to 15 N·m (11 lb ft).



6. Install the EGR valve inlet pipe to the intake and exhaust manifolds.

Tighten

1. Tighten the EGR valve inlet pipe intake manifold nut to 25 N·m (18 lb ft).
2. Tighten the EGR valve inlet pipe exhaust manifold nut to 30 N·m (22 lb ft).
3. Tighten the EGR valve inlet pipe clamp bolt to 25 N·m (18 lb ft).
7. Install the water outlet. Refer to Water Pump Replacement in Engine Cooling.
8. Connect the fuel pipes at the rear of the engine. Refer to Fuel Hose/Pipes Replacement - Engine Compartment in Engine Controls.
9. Install the bolt holding the fuel pipe bracket to the rear of the left cylinder head.

Tighten
Tighten the fuel pipe bracket bolt to 30 N·m (22 lb ft).

10. Connect the EVAP canister purge solenoid valve pipe. Refer to EVAP Canister Purge Solenoid Valve Replacement in Engine Controls.



11. Connect the vacuum brake booster hose to the intake manifold.
12. Install the distributor cap. Refer to Distributor Replacement in Engine Electrical.



13. Install the power steering pump mounting bracket and the three bolts and the nut.

Tighten
Tighten the power steering pump mounting bracket bolts and nuts to 41 N·m (30 lb ft).




14. Install the nuts holding the power steering pump rear bracket to the engine.

Tighten
Tighten the power steering pump rear bracket nuts to 41 N·m (30 lb ft).

15. Install the A/C compressor, if equipped. Refer to Air Conditioning Compressor Replacement in HVAC Systems with A/C - Manual.
16. Install the water pump pulley. Refer to Water Pump Replacement in Engine Cooling.



17. Install the accelerator control cable bracket to the throttle body.

Tighten
Tighten the bolt to 9 N·m (80 lb in).

Caution: In order to avoid possible injury or vehicle damage, always replace the accelerator control cable with a NEW cable whenever you remove the engine from the vehicle.

In order to avoid cruise control cable damage, position the cable out of the way while you remove or install the engine. Do not pry or lean against the cruise control cable and do not kink the cable. You must replace a damaged cable.
18. Install a NEW accelerator control cable. Refer to Accelerator Control Cable Replacement in Engine Controls.
19. Install the cruise control cable, if equipped to the throttle shaft and the accelerator cable bracket. Refer to Cruise Control Cable Replacement in Cruise Controls.



20. Install the battery ground cable bolt.

Tighten
Tighten the ground cable bolt to 35 N·m (26 lb ft).




21. Install the bolts holding the ground wires to the left cylinder head.

Tighten
Tighten the ground wire bolt to 35 N·m (26 lb ft).




22. Install the stud holding the ground wires to the right cylinder head.

Tighten
Tighten the stud to 35 N·m (26 lb ft).




23. Position the engine wiring harness.
24. Install the engine wiring harness in the retainers.
25. Connect the following electrical connectors:

•	The fuel meter body assembly

•	The EVAP canister purge solenoid valve

•	The idle air control (IAC) motor

•	The throttle position (TP) sensor

•	The A/C compressor high pressure switch, if equipped

•	The A/C clutch switch, if equipped

•	The exhaust gas recirculation (EGR) valve

•	The engine coolant temperature (ECT ) sensor

•	The ignition control module (ICM)

•	The generator

•	The crankcase position (CKP) sensor

26. Install the radiator. Refer to Radiator Replacement in Engine Cooling.
27. Install the inlet and outlet radiator hose to the engine. Refer to Radiator Hose Replacement in Engine Cooling.
28. Connect the heater hoses to the engine. Refer to Heater Hoses Replacement in Heating and Ventilation (Non A/C)



29. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
30. Install the transmission.

•	Refer to Transmission Replacement in Automatic Transmission - 4L60-E.

•	Refer to Transmission Replacement in Manual Transmission - New Venture.

31. Install the transfer case, if equipped.

•	Refer to Transfer Case Replacement in Transfer Case - NVG 236 (Two Speed Automatic).

•	Refer to Transfer Case Replacement (With Automatic Transmission) in Transfer Case - NVG 136-NP4 (One Speed Automatic).

32. Install the front propeller shaft (Four Wheel Drive vehicle only). Refer to Front Propeller Shaft Replacement in Propeller Shaft.



33. Install the transmission cover.

Tighten
Tighten the nut to 12 N·m (106 lb in).

34. Install the starter. Refer to Starter Motor Replacement in Engine Electrical.



35. Install the bolt holding the bracket for the starter wiring harness and if equipped, the transmission cooler lines.

Tighten
Tighten the bracket bolt to 12 N·m (106 lb in).

36. Connect the oil cooler pipes (RWD vehicle). Refer to Engine Oil Cooler Hose/Pipe Replacement in Engine Cooling.
37. Connect the remote oil filter inlet and outlet hoses (Four Wheel Drive vehicle). Refer to Remote Oil Filter Adapter Pipe Replacement .
38. Install the exhaust pipe to the exhaust manifolds. Refer to Exhaust Manifold Pipe Replacement in Engine Exhaust.
39. Install a NEW oil filter. Refer to Engine Oil and Oil Filter Replacement .
40. Install the braces from the engine to the transmission. Refer to Transmission Replacement in Manual Transmission - New Venture.
41. Install the underbody shields.
42. Lower the vehicle.
43. Fill the engine with oil. Refer to Engine Oil and Oil Filter Replacement .
44. Fill the cooling system with coolant. Refer to Cooling System Draining and Filling
45. Connect the battery negative cable. Refer to Battery Replacement in Engine Electrical.
46. Recharge the air conditioning system, if equipped. Refer to Refrigerant Recovery and Recharging in HVAC Systems with A/C - Manual.
47. Operate and test the engine. Refer to Engine Set-Up and Testing .