DTC P0144 HO2S Circuit High Voltage Bank 1 Sensor 3. Chevrolet S10 Pickup

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 1998 🢒 S10 Pickup - 4WD 🢒 Engine 🢒 Engine Controls - 4.3L 🢒 DTC P0144 HO2S Circuit High Voltage Bank 1 Sensor 3

Handling ESD Sensitive Parts Notice
Engine Controls Components
Heated Oxygen Sensors
OBD II Symbol Description Notice

Circuit Description

The heated oxygen sensor (HO2S) is a sensor designed to create a voltage relative to the oxygen content in the engine exhaust stream. The control module supplies the HO2S with signal high and low circuits. Ignition voltage and ground are supplied to the HO2S heater by independent circuits. The oxygen content of the exhaust indicates when the engine is operating lean or rich. When the HO2S detects that the engine is operating rich, the signal voltage is high, and decreases the signal voltage as the engine runs leaner. This oscillation above and below the bias voltage, sometimes referred to as activity or switching, can be monitored with the HO2S signal voltage.

The HO2S contains a heater that is necessary in order to quickly warm the sensor to operating temperature. The heater also maintains the operating temperature during extended idle conditions. The HO2S needs to be at a high temperature in order to produce a voltage. When the HO2S reaches operating temperature, the control module monitors the HO2S bias, or reference, voltage. It also monitors the HO2S signal voltage for Closed Loop fuel control. During normal Closed Loop fuel control operation, the control module will add fuel, or enrich the mixture, when the HO2S detects a lean exhaust content. The control module will subtract fuel, or "lean-out" the mixture, when the HO2S detects a rich exhaust condition.

Certain vehicle models utilize an oxygen sensor behind the catalytic converter in order to monitor catalyst efficiency.

This diagnostic trouble code (DTC) determines if the HO2S is functioning properly. It checks for an adequate number of HO2S voltage transitions above and below the bias range of 300-600 mV. This DTC sets when the vehicle control module (VCM) fails to detect a minimum number of voltage transitions above and below the bias range during the test period. Possible causes of this DTC are:

•	An open or a short to voltage on either the HO2S signal or HO2S low circuits

•	A malfunctioning HO2S

•	A problem in the HO2S heater or its circuit

•	A faulty HO2S ground

Conditions for Setting the DTC

•	No active TP sensor DTCs

•	No active EVAP system DTCs

•	No active IAT sensor DTCs

•	No active MAP sensor DTCs

•	No active ECT sensor DTCs

•	No active MAF sensor DTCs

•	No intrusive tests (i.e., EGR or Catalyst) in progress

•	No device control active

•	The system voltage is between 11.7-18 volts.

Rich Test

•	The system is in closed loop.

•	The air/fuel ratio is between 14.5-14.8

•	The throttle position is between 0-50 percent.

Decel Fuel Cut-Off (DFCO) Rich Test

•	DFCO mode active

•	The system is in closed loop.

•	The elapsed time since test was enabled is more than 2 seconds.

Decel Fuel Cut-Off (DFCO)

•	DFCO mode active

•	The system is in closed loop.

•	The elapsed time since test was enabled is more than 2 seconds.

Conditions for Setting the DTC

Rich Test

The O2 sensor voltage is more than 994 mV for more than 110 seconds.

Decel Fuel Cut-Off (DFCO) Rich Test

The O2 sensor voltage is more than 469 mV for more than 40 seconds.

Action Taken When the DTC Sets

•	The control module illuminates the malfunction indicator lamp (MIL) if a failure is detected during 2 consecutive key cycles.

•	The control module sets the DTC and records the operating conditions at the time the diagnostic failed. The failure information is stored in the scan tool Freeze Frame/Failure Records.

Conditions for Clearing the MIL or DTC

•	The control module turns OFF the MIL after 3 consecutive drive trips when the test has run and passed.

•

A history DTC will clear if no fault conditions have been detected for 40 warm-up cycles. A warm-up cycle occurs when the coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant reaches a temperature that is more than 70°C (158°F) during the same ignition cycle.

•	Use a scan tool in order to clear the DTCs.

Diagnostic Aids

Check the following items:

•	The fuel pressure: If the pressure is too high, the system will run rich. The VCM can compensate for some increase; however, if the pressure gets too high, the DTC may set. Refer to Symptoms .

•	A rich injector. Perform a poppet nozzle test. Refer to Fuel Injector Balance Test for the 4.3L.

•	A leaking injector. Refer to Symptoms .

•	Fuel contaminated oil

•	EVAP canister purge: Check for a fuel saturation. If full of fuel, check the canister control and hoses. Refer to Evaporative Emission Control System Diagnosis .

•	Leaking fuel pressure regulator diaphragm by checking the vacuum line to the regulator for fuel.

•	The TP sensor: An intermittent TP sensor output causes the system to run rich due to a false indication of the throttle moving.

•	False rich indication due to silicon contamination of the heated oxygen sensor. A DTC P0144 accompanied by a lean driveability conditions and a powdery white deposit on the sensor indicates a false rich indication.

An intermittent may be caused by any of the following conditions:

•	A poor connection

•	Rubbed through wire insulation

•	A broken wire inside the insulation

Thoroughly check any circuitry that is suspected of causing the intermittent complaint. Refer to Intermittents and Poor Connections Diagnosis in Wiring Systems.

If a repair is necessary, refer to Wiring Repairs or Connector Repairs in Wiring Systems.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

In order to determine if the engine is rich during Deacceleration Fuel Cut-Off (DFCO) operate the vehicle up to highway speed conditions and release the accelerator pedal allowing the vehicle to coast in gear. Monitor the scan tool HO2S voltage and the DFCO parameter. A rich condition will cause HO2S voltage to be above 468 mV during DFCO.

An HO2S contaminated by silicon will have a white, powdery deposit on the portion of the HO2S that is exposed to the exhaust stream. The usual cause of silica contamination is the use of unapproved silicon RTV engine gasket material or the use of silicon based sprays or fluids within the engine. If the cause of this contamination is not corrected, the replacement HO2S will also get contaminated.

Monitor the HO2S voltage of the opposite bank sensor. If the voltage activity of the opposite bank sensor is similar to the voltage activity of the suspect sensor check for lean conditions that would affect both cylinder banks. An opposite bank sensor with normal HO2S voltage activity indicates the suspect HO2S needs replacement or a lean condition exists only on the suspect HO2S cylinder bank.

This step checks the HO2S High signal circuit for a short to voltage.

Step

Action

Value(s)

Yes

Important: Before clearing the DTCs, use the scan tool Capture Info function to save the Freeze Frame and the Failure Records for reference. The control module's data is deleted once the Clear DTC Information function is used.

Was the Powertrain On-Board Diagnostic (OBD) System Check performed?

Go to Step 2

Go to Powertrain On Board Diagnostic (OBD) System Check

Run the engine until normal operating temperature is reached.
Using the scan tool, monitor the HO2S voltage for the sensor that applies to this DTC.

Is the HO2S voltage fixed greater than the value specified?

994 mV

Go to Step 4

Go to Step 3

The condition that set this DTC is not present. This DTC may have been set by one of the following conditions:

•	A signal wire intermittently shorted to voltage

•	HO2S connector water intrusion

•	A silicon contaminated HO2S

•	An intermittent rich engine condition such as the following:

-	EVAP canister purge condition

-	Fuel contamination engine oil

-	Incorrect fuel pressure

-	A leaking fuel pressure pressure regulator

-	Rich fuel injectors

-	An inaccurate MAF sensor

-	A rich engine condition during DFCO operation

Repair any of the above or similar engine conditions as necessary.

Did you find a problem?

Go to Step 10

Go to Diagnostic Aids

Turn OFF the ignition.
Disconnect the HO2S connector for the sensor that applies to this DTC.
Jumper the HO2S LOW circuit terminal (engine harness side) to a known good ground.
Turn ON the ignition while leaving the engine OFF.
Using the scan tool, monitor the HO2S voltage for the sensor that applies to this DTC.

Is the HO2S voltage within the specified value range?

351-551 mV

Go to Step 5

Go to Step 6

The HO2S may be detecting a lean exhaust condition. Check for one of the following conditions:

•	HO2S connector water intrusion

•	Silicon contaminated HO2S

•	Fuel Contaminated engine oil

•	EVAP canister purge condition

•	Incorrect fuel pressure

•	Rich fuel injectors

•	An inaccurate MAF sensor

Repair any of the above or similar engine conditions as necessary.

Did you find a problem?

Go to Step 10

Go to Step 8

Turn OFF the ignition.
Remove the jumper from the HO2S LOW circuit terminal.
Disconnect the VCM connector that contains the HO2S HIGH signal circuit.
Turn ON the ignition leaving the engine OFF.
Using a J 39200 DMM measure the voltage between the HO2S HIGH signal circuit VCM connector terminal (harness side) and ground.

Is the voltage greater than the specified value?

20 mV

Go to Step 7

Go to Step 9

Repair the short to voltage in the HO2S HIGH signal circuit. Refer to Wiring Repairs .

Is the action complete?

Go to Step 10

Important: Brfore replacing a contaminated HO2S, determine and repair the cause of the contamination.

Replace the HO2S. Refer to Heated Oxygen Sensor Replacement .

Is the action complete?

Go to Step 10

Replace the VCM.
Program the VCM. Refer to VCM Replacement/Programming .
Perform the VTD Password Learn Procedure. Refer to Password Learn .
Perform the Crankshaft Variation Learn Procedure. Refer to Crankshaft Position System Variation Learn .

Is the replacement complete?

Go to Step 10

Important: If a rich engine condition was repaired, inspect the engine oil for fuel contamination and replace the engine oil as necessary.

Using the scan tool, clear the DTCs.
Operate the vehicle under the Conditions for running the DTC.
Observe the DTC Status for this DTC.

Did this DTC run and pass?

Go to Step 11

Go to Step 2

Does the scan tool display any additional undiagnosed DTCs?

Go to the applicable DTC table

System OK