| Table 1: | WSS Temperature vs. Sensor Resistance (S-Pickup only) |
| Table 2: | WSS Temperature vs. Sensor Resistance (S-Utility and T-Truck) |
Circuit Description
The wheel speed sensor coil emits an electromagnetic field. A toothed ring on the wheel passes by the wheel speed sensor and disrupts this electromagnetic field. The disruption in the field causes the wheel speed sensor to produce a sinusoidal (AC) voltage signal. The frequency and amplitude of the sinusoidal (AC) voltage signal are proportional to the speed of the wheel. The amplitude of the wheel speed signal is also directly related to the distance between the wheel speed sensor coil and the toothed ring. This distance is referred to as the air gap.
Conditions for Setting the DTC
| • | The average wheel speed for all wheel signals is greater than 40 km/h (25 mph). |
| • | The average left front wheel speed is greater than 40 km/h (25 mph). |
| • | No speed signal input to the EBCM from the left front wheel speed sensor for 15ms. Anything which suddenly prevents (intermittent) the left front wheel speed signal to drop to zero while the vehicle is moving greater than 40 km/h (25 mph). |
Action Taken When the DTC Sets
| • | The ABS indicator lamp turns on |
| • | The ABS disables |
DTC C0227 is a Condition Latched DTC, which indicates that the above actions remain true only as long as the condition persists.
Conditions for Clearing the DTC
| • | Repair the conditions responsible for setting the DTC. |
| • | Use the Scan Tool clear DTCs function. |
Diagnostic Aids
Any of the following conditions may cause an intermittent malfunction:
| • | A poor connection |
| • | Wire insulation that is rubbed through |
| • | A wire breaks inside the insulation |
Thoroughly check any circuitry that is suspected of causing the intermittent complaint for the following conditions:
| • | Backed out terminals |
| • | Improper mating |
| • | Broken locks |
| • | Improperly formed or damaged terminals |
| • | Poor terminal to wiring connections |
| • | Physical damage to the wiring harness |
If the customer says that the ABS indicator lamp is on only during humid conditions such as rain, snow, or vehicle wash, then thoroughly inspect all wheel speed sensor circuits for signs of water intrusion. Use the following procedure:
- Spray the suspected area with a 5% salt water solution (two teaspoons of salt to 12 oz. of water).
- Drive the vehicle above 24 km/h (15 mph) for at least 30 seconds.
If the DTC returns, replace the suspected harness.
When inspecting a wheel speed sensor, inspect the sensor terminals and the harness connector for corrosion. If evidence of corrosion exists, then replace the wheel speed sensor. Refer to Wheel Speed Sensor Replacement .
Resistance of the wheel speed sensor will increase with an increase in sensor temperature. Refer to the following tables for temperature/resistance values.
°C | °F | Ohms |
|---|---|---|
Temperature vs Resistance Values (Approximate) | ||
-40 to 4 | -40 to 40 | 3915 to 5820 |
5 to 43 | 41 to 110 | 4760 to 6800 |
44 to 93 | 111 to 200 | 5560 to 8040 |
94 to 150 | 201 to 302 | 6600 to 9406 |
°C | °F | Ohms |
|---|---|---|
Temperature vs Resistance Values (Approximate) | ||
-40 to 4 | -40 to 40 | 920 to 1440 |
5 to 43 | 41 to 110 | 1125 to 1700 |
44 to 93 | 111 to 200 | 1305 to 2000 |
94 to 150 | 201 to 302 | 1530 to 2310 |
Test Description
The numbers below refer to the steps in the diagnostic table:
-
This step checks the EBCM 4-way connector for looseness, corrosion, etc.
-
This step uses the wheel speed sensor resistance check to help isolate an intermittent connection.
-
This step checks the left front wheel speed sensor for the proper resistance.
-
This step checks for proper mounting and orientation of the left front wheel speed sensor.
Step | Action | Value(s) | Yes | No |
|---|---|---|---|---|
1 | Was the Diagnostic System Check performed? | -- | Go to A Diagnostic System Check | |
2 |
Are all connections clean and tight? | -- | ||
Using a J 39200 , measure the resistance between terminals D and A of the 4-way EBCM harness connector. Wiggle the WSS harness in various locations between the sensor and the EBCM while performing this measurement. Is the resistance measurement within the specified range without fluctuation when the harness is wiggled? (Refer to the WSS Temperature vs. Sensor Resistance tables for applicable sensor resistance values. The values in these tables are for the temperature of the sensor, not the air temperature.) | -- | |||
Is the resistance measurement within the specified range? (Refer to the WSS Temperature vs. Sensor Resistance tables for applicable sensor resistance values. The values in these tables are for the temperature of the sensor, not the air temperature.) | -- | |||
Is the wheel speed sensor and tone wheel in good condition? | -- | |||
6 | Make necessary repairs to the 4-way EBCM harness connector. Is the repair complete? | -- | Go to A Diagnostic System Check | -- |
7 | Repair the open, high resistance or short in CKTs 830 or 873. Is the repair complete? | -- | Go to A Diagnostic System Check | -- |
8 | Replace the left front wheel speed sensor. Refer to Wheel Speed Sensor Replacement . Is the repair complete? | -- | Go to A Diagnostic System Check | -- |
9 | Malfunction is intermittent.
Refer to Diagnostic aids for more information. Is the repair complete? | -- | Go to A Diagnostic System Check | -- |
10 | Make necessary repairs. Is the repair complete? | -- | Go to A Diagnostic System Check | -- |
