Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: HVAC Schematics Connector End View Reference: HVAC Connector End Views DEFINITION: The A/C compressor clutch will not disengage when an A/C request has not been made and a Powertrain DTC has not been set. | |||
1 | Did you perform the HVAC Diagnostic System Check? | Go to Step 2 | |
Is the A/C compressor clutch engaged? | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems | |
3 | With a scan tool, observe the A/C Request Signal parameter in the Roof/Door Module (RDM) data list. Does the scan tool indicate the A/C Request Signal parameter is Yes? | Go to Step 6 | Go to Step 4 |
4 | Disconnect the A/C compressor clutch relay. Does the A/C compressor clutch disengage? | Go to Step 5 | Go to Step 7 |
5 | Connect a test lamp between the A/C compressor clutch relay control circuit and the battery positive voltage circuit of the A/C compressor clutch relay. Does the test lamp illuminate? | Go to Step 8 | Go to Step 11 |
6 | Disconnect the evaporator temperature sensor. Does the A/C compressor clutch disengage? | Go to Step 9 | Go to Step 10 |
7 | Test the supply voltage circuit of the A/C compressor clutch for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 12 |
8 | Test the control circuit of the A/C compressor clutch relay for a short to ground. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 15 |
9 | Test the A/C request signal circuit of the HVAC control module for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 13 |
10 | Test the A/C request signal circuit of the RDM for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 14 |
11 | Inspect for poor connections at the A/C compressor clutch relay. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 16 |
12 | Inspect for poor connections at the harness connector of the A/C compressor clutch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 17 |
13 | Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 18 |
14 | Inspect for poor connections at the harness connector of the RDM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 19 |
15 | Inspect for poor connections at the harness connector of the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 21 | Go to Step 20 |
16 | Replace the A/C compressor clutch relay. Did you complete the replacement? | Go to Step 21 | -- |
17 | Replace the A/C compressor. Refer to Air Conditioning Compressor Replacement in Heating, Ventilation and Air Conditioning. Did you complete the replacement? | Go to Step 21 | -- |
18 |
Important: Perform the recalibration procedure for the HVAC control module. Replace the HVAC control module. Refer to HVAC Control Module Replacement . Did you complete the replacement? | Go to Step 21 | -- |
19 |
Important: Perform the setup procedure for the RDM. Replace the RDM. Refer to Folding Top Control Module Replacement in Roof. Did you complete the replacement? | Go to Step 21 | -- |
20 |
Important: Program the PCM. Replace the PCM. Refer to Powertrain Control Module Replacement in Engine Controls - 4.8L, 5.3L, and 6.0L. Did you complete the replacement? | Go to Step 21 | -- |
21 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 3 |
