Circuit Description
The folding top stowage compartment lid extension panel cylinder position sensors are mounted on each end of the folding top stowage compartment lid extension panel cylinder. The sensors are supplied with a 12-volt reference from the roof door module (RDM). When the folding top stowage compartment lid extension panel cylinder reaches full extended travel, the retracted sensor will be inactive and the extended sensor will be active sending a voltage signal to the RDM between 0.35 and 1.33 volts on the extended signal circuit. When the folding top stowage compartment lid extension panel cylinder reaches full retracted travel, the extended sensor will now be inactive and the retracted sensor will be active sending a voltage signal to the RDM between 0.35 and 1.33 volts on the retracted signal circuit. The RDM monitors the folding top stowage compartment lid extension panel cylinder position sensors at least once every 200 milliseconds.
Conditions for Running the DTC
| • | The battery voltage is between 9-16 volts. |
| • | Ignition is in the Accessory or Run position or retained accessory power (RAP) is active. |
| • | A request for folding top operation has been received by the RDM, and the RDM attempts to operate the folding top. |
Conditions for Setting the DTC
| • | If the RDM detects the folding top stowage compartment lid extension panel cylinder position sensor extended signal circuit or folding top stowage compartment lid extension panel cylinder position sensor retracted signal circuit is shorted to ground or open, DTC B3665 will set. |
| • | If the RDM detects the folding top stowage compartment lid extension panel cylinder position sensor extended signal circuit or folding top stowage compartment lid extension panel cylinder position sensor retracted signal circuit is shorted to power, DTC B3665 will set as current and B1310, B1311, B3666, B3665, and B3667 will be set in history. |
| • | If the 12-volt reference circuit is open DTC B3665 will set. |
| • | If both folding top stowage compartment lid extension panel cylinder position sensors are active simultaneously, DTC B3665 will set. |
Action Taken When the DTC Sets
| • | Stores current and history DTCs in the RDM. |
| • | The folding top operation is suspended. |
Conditions for Clearing the DTC
| • | This DTC will clear on the current status after the condition for setting the fault is corrected. |
| • | A history DTC will clear after 50 consecutive ignition cycles without a fault present. |
| • | History and current DTC can be cleared using the scan tool. |
Diagnostic Aids
The code that is set as current should be diagnosed first due to multiple codes set in history.
If the DTC does not reset after the code is cleared, then the sensor may be the source of an intermittent fault. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Folding Top Schematics Connector End View Reference: Power Roof Systems Connector End Views | |||
1 | Did you perform the Power Roof Diagnostic System Check? | Go to Step 2 | |
2 |
Does the scan tool display the appropriate data in the each position? | Go to Step 3 | Go to Step 4 |
3 |
Does the scan tool display the appropriate data in the each position? | Go to Diagnostic Aids | Go to Step 4 |
4 |
Does the test lamp illuminate? | Go to Step 5 | Go to Step 7 |
5 | With the test lamp connected to a good ground, test the affected folding top compartment lid extension panel cylinder position sensor extended or retracted signal circuit. Does the test lamp illuminate? | Go to Step 10 | Go to Step 6 |
6 | Test the affected folding top compartment lid extension panel cylinder position sensor extended or retracted signal circuit for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 8 |
7 | Test the 12-volt reference circuit at the affected folding top stowage compartment lid extension panel cylinder position extended or retracted sensor for an open or a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 9 |
8 | Inspect for poor connections at the harness connector of the affected folding top stowage compartment lid extension panel cylinder position extended or retracted sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 11 |
9 | Inspect for poor connections at the harness connector of the RDM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 13 | Go to Step 12 |
10 | Repair the short to battery voltage in the affected folding top compartment lid extension panel cylinder position sensor extended or retracted signal circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 13 | -- |
11 | Replace the inoperative folding top stowage compartment lid extension panel cylinder position extended or retracted sensor. Refer to Folding Top Stowage Compartment Lid Hydraulic Cylinder Extension Panel Replacement . Did you complete the replacement? | Go to Step 13 | -- |
12 |
Important: Always perform the reinitialization of the power windows procedure for the roof door module (RDM).
Did you complete the replacement? | Go to Step 13 | -- |
13 |
Does the DTC reset? | Go to Step 2 | System OK |
