GM Service Manual Online
For 1990-2009 cars only

Interior Lamps

The interior lighting consist of the following two groups. This first group includes lamps that may not be dimmed.

    • The courtesy lamps
    • The instrument panel (I/P) compartment lamp
    • The reading lamps
    • The vanity mirror lamps

Courtesy Lamps

The courtesy lamp supply voltage circuit provides voltage to the interior illumination lamps which are all located on the underside of the inside rear view mirror. If a door is opened, the courtesy lamps illuminate. After all the doors have been closed, the courtesy lamps will remain illuminated approximately 15 seconds after the last door closes. The courtesy lamps will also turn ON prior to any door being opened and will remain illuminated approximately 40 seconds when the driver removes the ignition key. The body control module (BCM) will immediately turn off the courtesy lamps if a door lock command is received with all of the doors closed, or if the ignition switch is turned to either the ON or RUN position.

Reading Lamps

The inadvertent courtesy lamp supply circuit provides voltage for the reading lamps that are on the underside of the inside rear view mirror. These lamps may be manually turned ON or OFF with the switches on the mirror.

Keyless Entry Interior Illumination

When the driver uses the door key in order to unlock the doors, the body control module (BCM) receives a door unlock signal. The BCM must have inputs that indicate that the ignition switch is OFF and all the doors are closed. The BCM will then illuminate the courtesy lamps. The courtesy lamps will remain illuminated for approximately 15 seconds after the door is closed. If the door locks are activated to the LOCK position, or if the ignition switch is turned to either the RUN or CRANK position, the courtesy lamps will turn OFF immediately.

When the driver uses the remote function actuator transmitter to unlock the doors or presses the panic button, the BCM will keep the courtesy lamps ON for approximately 15 seconds. If the door locks are activated to the UNLOCK or LOCK position or if the ignition switch is turned to either the RUN or CRANK position, the courtesy lamps will turn OFF immediately. The BCM will also keep the courtesy lamps ON for approximately 40 seconds after an alarm event is completed.

Vanity Lamps

The inadvertent courtesy lamp supply circuit of the body control module (BCM) provides battery positive voltage to each vanity mirror lamp. When the vanity mirror cover on the sunshade is opened, a switch closes to provide a ground circuit and the vanity lamp illuminates.

I/P Compartment Lamp

The inadvertent courtesy lamp supply circuit of the body control module (BCM) also provides battery positive voltage to instrument panel (I/P) compartment lamp. When the I/P compartment is opened, a switch closes to provide a ground circuit and the I/P compartment lamp illuminates.

Battery Rundown Protection/Inadvertent Power

The body control module (BCM) inadvertent courtesy lamp supply circuit provides battery positive voltage to all of the interior reading lamps, instrument panel (I/P) compartment lamp, and both visor vanity mirror lamps. In the event that any of these lamps were to remain illuminated for a period of more than 20 minutes with the ignition switch in the OFF position, the BCM will deactivate the inadvertent courtesy lamp supply circuit to prevent a total battery discharge condition. Only when the ignition switch is cycled back to the RUN position will the BCM reset the internal timer and reactivate the inadvertent courtesy lamp supply circuit.

The BCM also utilizes the inadvertent courtesy lamp supply circuit as a courtesy lamp request signal circuit when none of the lamps in the circuit are illuminated. When a lamp switch is activated, the BCM receives the request for lamp illumination and switches to supplying voltage to the inadvertent courtesy lamp supply circuit.

Interior Lamps Dimming

The second group includes lamps which may be dimmed. This group may use a combination of vacuum fluorescent (VF) illumination and of incandescent lamps.

    • Console, and instrument panel (I/P) switches
    • HVAC control head assembly
    • Radio and steering wheel controls
    • The instrument panel cluster (IPC)

When the ignition switch is turned to the RUN position, the radio's vacuum fluorescent (VF) displays turn ON at maximum brightness. When the park lamps are ON, all incandescent back lighting turn on at the dimming level indicated by the I/P dimmer switch. At the same time all VF displays dim to match the indicated dimming level. The panel dimmer switch potentiometer is an input to the body control module (BCM). When the driver selects a dimming setting by moving the I/P dimming switch potentiometer, all incandescent back lighting lamps are provided with a specific voltage. The incandescent back lighting lamps are then grounded at G200 and G300. When the I/P dimmer switch is moved from MIN to MAX, all VF displays, as well as all incandescent back lighting respond from minimum intensity to maximum brightness in response to the I/P dimmer switch.