The driver-side deployment loop consists the following components:
• | An inflatable restraint side-impact module - LF |
• | The inflatable restraint side-impact module wiring harness |
• | The side-impact module - LF high circuits |
• | The side-impact module - LF module low circuits |
A shorting bar is used within the side-impact module - LF connector. The shorting bar will short together the side-impact module - LF high circuit, and the side-impact module - LF low circuit when the connector is disconnected. This helps prevent unwanted deployment of the inflator module during servicing. During a side or frontal crash of sufficient force, the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop. This flow of current will deploy the side-impact module - LF. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored in memory.
This diagnostic procedure supports the following DTCs:
• | DTC B0040 Left Front/Driver Side Deployment Loop Resistance Low |
• | DTC B0041 Left Front/Driver Side Deployment Loop Open |
• | DTC B0045 Left Front/Driver Side Deployment Loop Voltage Out of Range |
Ignition 1 voltage is within the normal operating voltage range.
• | DTC B0040 will set when the side-impact module - LF deployment loop resistance is less than 1.3 ohms for 500 milliseconds. |
• | DTC B0041 will set when one of the following conditions occurs: |
- | A side-impact module - LF high circuit is less than 2.4 volts and the side-impact module - LF deployment loop is more than 6 ohms for 500 milliseconds. |
- | A side-impact module - LF deployment loop resistance is more than 4.8 ohms for 500 milliseconds. |
• | DTC B0045 will set when one of the following conditions occur: |
- | A side-impact module - LF high and/or low circuits is short-to-ground or short-to-voltage for 500 milliseconds. |
- | A side-impact module - LF high circuit is less than 2.4 volts, and the side-impact module - LF deployment loop resistance is less than 6 ohms for 500 milliseconds. |
The SDM commands the AIR BAG indicator ON via Class 2 serial data.
• | The condition responsible for setting the DTC not currently present, and the scan tool Clear DTCs function is used. |
• | A history DTC will clear once 255 malfunction-free ignition cycles have occurred. |
The following are possible causes of the malfunction:
• | A short between the side-impact module - LF high circuits and low circuits. |
• | An open or a high resistance in the side-impact module - LF high circuits or low circuits. |
• | A short to ground or a short to voltage in the side-impact module - LF high circuits or low circuits. |
• | A malfunctioning side-impact module - LF connector |
• | A malfunctioning SDM connector |
• | A malfunctioning side-impact module - LF |
• | A malfunctioning SDM |
Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction. If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections .
The numbers below refer to the step numbers on the diagnostic table.
Step | Action | Yes | No |
---|---|---|---|
Schematic Reference: SIR Schematics Connector End View Reference: SIR Connector End Views | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |
2 |
Does connector exhibit any signs of damage or corrosion? | Go to Step 3 | Go to Step 4 |
3 |
Did you complete the repair? | Go to Step 9 | -- |
4 |
Does the scan tool indicate that DTC B0040, B0041, or B0045 are current? | Go to Step 5 | Go to Step 7 |
5 |
Did you find and correct the condition? | Go to Step 9 | Go to Step 6 |
Did you find and correct the condition? | Go to Step 9 | Go to Step 8 | |
7 |
Did you complete the replacement? | Go to Step 9 | -- |
8 |
Did you complete the replacement? | Go to Step 9 | -- |
9 |
Does the DTC reset? | Go to Step 2 | System OK |