GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2006 🢒 SSR 🢒 Body 🢒 Roof 🢒 DTC B3683

Circuit Description

The roof door module (RDM) monitors the folding top outer latch striker position switch at least once every 200 milliseconds. The folding top outer latch striker position switch is a three position switch that the RDM uses to determine roof position in relation to the header. The switch is tripped by the dowel pin on the folding top front panel as the top approaches the header. The switch tells the RDM that the roof is aligned and the latching process can begin.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC B3683 Convertible Top/Moveable Roof Header Ready to Latch Left Sensor Circuit

Conditions for Running the DTC
    • The battery voltage is between 9-16  volts.
    • Ignition is in the Accessory or Run position or retained accessory power (RAP) is active.
    • A request for folding top operation has been received by the RDM, and the RDM attempts to operate the folding top.

Conditions for Setting the DTC
    • If the RDM detects an open or short to voltage in the folding top outer latch striker over center signal circuit , the DTC will set.
    • If the RDM detects an open in the ground circuit of the folding top outer latch striker position switch, the DTC will set.
    • If the RDM detects that the dowel pin is engaged and the RDM commands the roof down for approximately 30 seconds and the folding top cylinder position sensor is active, the DTC will set.
    • If the RDM commands the roof up for approximately 30 seconds and the dowel pin is not engaged and the folding top cylinder position sensor is active, the DTC will set.

Action Taken When the DTC Sets
    • Stores a current DTC B3683 in the RDM.
    • Folding top operation is suspended.

Conditions for Clearing the DTC
    • This DTC will clear on the current status after the condition for setting the fault is corrected.
    • A history DTC will clear after 50 consecutive ignition cycles without a fault present.
    • History and current DTC can be cleared using the scan tool.

Diagnostic Aids

If the DTC does not reset after the code is cleared, then the switch may be the source of an intermittent fault. Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.

Step

Action

Yes

No

Schematic Reference: Folding Top Schematics

Connector End View Reference: Power Roof Systems Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2
  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Roof Dowel Pin Switch parameter in the data list for the roof door module (RDM).

With the roof stowed, the Roof Dowel Pin Switch should display Disengaged.

With the roof closed, the Roof Dowel Pin Switch should display Engaged.

Does the scan tool display the appropriate state?

Go to Step 3

Go to Step 4

3
  1. Activate the folding top.
  2. With the scan tool, observe the Roof Dowel Pin Switch data parameter.

Does the Roof Dowel Pin Switch parameter change state?

Go to Diagnostic Aids

Go to Step 4

4
  1. Turn OFF the ignition.
  2. Disconnect the folding top outer latch striker position switch.
  3. Turn ON the ignition, with the engine OFF.
  4. With a scan tool, observe the Roof Dowel Pin Switch parameter.

Does the scan tool display Transition or Engaged?

Go to Step 5

Go to Step 6

5
  1. Connect a test lamp to battery positive voltage.
  2. Probe the folding top outer latch striker position switch ground circuit.

Does the test lamp illuminate?

Go to Step 9

Go to Step 10

6
  1. Probe the folding top outer latch striker over center signal circuit with a 3-amp fused jumper connected to the folding top outer latch striker position switch ground circuit.
  2. Observe the Roof Dowel Pin Switch parameter in the scan tool.

Does the scan tool display Over Center or Disengaged or does the jumper fuse open?

Go to Step 9

Go to Step 7

7

Test for an open, high resistance, short to ground, or short to voltage in the folding top outer latch striker over center signal circuit. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 13

Go to Step 8

8

Inspect for poor connections at the harness connector of the RDM. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 13

Go to Step 11

9

Inspect for the following:

    • Proper dowel pin to folding top outer latch striker position switch alignment. Refer to Folding Top Latch Replacement - Side
    • Poor connections at the harness connector of the folding top outer latch striker position switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 13

Go to Step 12

10

Repair the open in the folding top outer latch striker position switch ground circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 13

--

11

Important: Always perform the reinitialization of the power windows procedure for the RDM.

  1. Replace the RDM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.
  2. Perform the reinitialization of the power windows procedure for the RDM. Refer to Power Window Reinitialization in Doors.

Did you complete the replacement?

Go to Step 13

--

12

Replace the folding top outer latch striker position switch. Refer to Folding Top Latch Replacement - Side .

Did you complete the replacement?

Go to Step 13

--

13
  1. Use the scan tool in order to clear the DTCs.
  2. Operate the vehicle within the Conditions for Running the DTC.

Does the DTC reset?

Go to Step 2

System OK