GM Service Manual Online
For 1990-2009 cars only
Makes
🢒
Chevrolet
🢒
2009
🢒
Silverado - 2WD
🢒
Engine
🢒
Engine Electrical
🢒 Battery Positive Cable Replacement
Battery Positive Cable Replacement With LU3
Removal Procedure
Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Remove the under hood junction block cover.
Lift the junction block retainers from the locked position (3) and rotate the retainers to the open position (1).
Remove the junction block.
Remove the positive battery cable connector (1) from the underhood bussed electrical center (UBEC).
Remove the mega fuse cover.
Remove the starter solenoid cable nut (2) from the mega fuse.
Remove the starter solenoid cable (1) terminal from the mega fuse stud.
Remove the positive battery cable channel from the studs on the plenum front panel.
Remove the positive battery cable clips from the studs on the plenum front panel.
Remove the positive battery cable terminal from the mega fuse stud.
Remove the positive battery cable channel from the studs.
Remove the positive battery cable from the vehicle.
Installation Procedure
Install the positive battery cable to the vehicle.
Install the positive battery cable terminal to the mega fuse stud.
Install the positive battery cable channel at the plenum front panel.
Install the positive battery cable clips to the studs on the plenum front panel.
Install the starter solenoid cable (1) terminal to the mega fuse stud.
Caution:
Refer to
Fastener Caution
in the Preface section.
Install the starter solenoid cable nut (2) to the mega fuse and tighten to
9 N·m (80 lb in)
.
Install the mega fuse cover.
Install the positive battery cable connector (1) to the UBEC.
Ensure the junction block retainers are in the open position (1).
Position and align the junction block to the 4 bracket pivots (2), once the pivots are engaged, push the retainer down into the locked position (3).
Install the under hood junction block cover.
Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Battery Positive Cable Replacement With V8 Engine
Removal Procedure
Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Remove the under hood junction block cover.
Lift the junction block retainers from the locked position (3) and rotate the retainers to the open position (1).
Remove the junction block.
Remove the positive battery cable connector (1) from the underhood bussed electrical center (UBEC).
Remove the mega fuse cover.
Remove the generator battery jumper cable to mega fuse nut (3).
Remove the generator battery jumper cable terminal (4) from the mega fuse stud.
Remove the positive battery cable channel from the studs on the plenum front panel.
Remove the positive battery cable clips from the studs on the plenum front panel.
Remove the positive battery cable terminal from the mega fuse stud.
Remove the positive battery cable channel from the studs.
Remove the positive battery cable from the vehicle.
Installation Procedure
Install the positive battery cable to the vehicle.
Install the positive battery cable terminal to the mega fuse stud.
Install the positive battery cable channel at the plenum front panel.
Install the positive battery cable clips to the studs on the plenum front panel.
Install the generator battery jumper cable terminal (4) to the mega fuse stud.
Caution:
Refer to
Fastener Caution
in the Preface section.
Install the generator battery jumper cable to mega fuse nut (3) and tighten to
9 N·m (80 lb in)
.
Install the mega fuse cover.
Install the positive battery cable connector (1) to the UBEC.
Ensure the junction block retainers are in the open position (1).
Position and align the junction block to the 4 bracket pivots (2), once the pivots are engaged, push the retainer down into the locked position (3).
Install the under hood junction block cover.
Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Battery Positive Cable Replacement With LMM
Removal Procedure
Disconnect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.
Remove the intake manifold cover. Refer to
Intake Manifold Cover Replacement
.
Remove the underhood junction block cover.
Lift the junction block retainers from the locked position (3) and rotate the retainers to the open position (1).
Reposition the junction block.
Remove the positive battery cable connector (1) from the underhood bussed electrical center (UBEC).
Disconnect the positive battery cable (1) from the glow plug control module.
Remove the mega fuse cover.
Remove the positive battery cable to mega fuse nuts (1).
Remove the positive battery cable terminals from the mega fuse studs.
Remove the positive battery cable clip nuts (2) from the studs on the plenum front panel.
Remove the positive battery cable clip (1) from the stud on the plenum front panel.
Remove the positive battery cable clips (1) from the studs on the plenum front panel.
Remove the positive battery cable from the vehicle.
Installation Procedure
Install the positive battery cable to the vehicle.
Install the positive battery cable clips (1) onto the studs on the plenum front panel.
Install the positive battery cable clip (1) onto the stud on the plenum front panel.
Caution:
Refer to
Fastener Caution
in the Preface section.
Install the positive battery cable clip nuts (2) to the studs on the plenum front panel and tighten to
3 N·m (27 lb in)
.
Install the positive battery cable terminals onto the mega fuse studs.
Install the positive battery cable to mega fuse nuts (1) and tighten to
7.5 N·m (66 lb in)
.
Install the mega fuse cover.
Connect the positive battery cable (1) to the glow plug control module.
Install the positive battery cable connector (1) to the UBEC.
Ensure that the junction block retainers are in the open position (1).
Position and align the junction block to the 4 bracket pivots (2), once the pivots are engaged, push the retainers down into the locked position (3).
Install the underhood junction block cover.
Install the intake manifold cover. Refer to
Intake Manifold Cover Replacement
.
Connect the negative battery cable. Refer to
Battery Negative Cable Disconnection and Connection
.