Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of this diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC C0899 00: Device Voltage Low - EBCM (JF3/JF7/JH6/JH7)DTC C0899 03: Device Voltage Low - EBCM (JL4)
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
B+ | C0899 00, C0899 03 | C0899 00, C0899 03 | -- | -- |
Ground | -- | C0899 00, C0899 03 | -- | -- |
Typical Scan Tool Data
Circuit | Short to Ground | Open | Short to Voltage |
|---|---|---|---|
Operating Conditions: Ignition ON, engine OFF. Parameter Normal Value: 12.6 V | |||
B+ | 0.0 V | 0.0 V | 12.6 V |
Circuit/System Description
The electronic brake control module (EBCM) monitors the battery positive (B+) voltage level available for system operation. A low voltage condition prevents the system from operating properly. If low voltage is detected by the EBCM, then DTC C0899 sets.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
The ignition voltage available to the EBCM is less than 9 V for 100 msec.
Action Taken When the DTC Sets
| • | The traction control system (TCS) and vehicle stability enhancement system (VSES) are disabled for the duration of the ignition cycle. |
| • | The vehicle dynamics caution (VDC) indicator turns ON. |
Conditions for Clearing the DTC
| • | The condition for the DTC is no longer present. |
| • | The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles. |
Diagnostic Aids
| • | A low voltage DTC in multiple modules indicates a concern in the charging system. |
| • | Inspect the ground connection G300 to verify that it is clean and tight. |
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
| • | ABS Description and OperationABS Description and Operation less than 8600 GVW |
| ABS Description and OperationABS Description and Operation greater than 8600 GVW |
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Verification
- Engine running, accessories OFF, measure and record the battery voltage at the battery terminals. The voltage should be between 12.6 and 15.0 V.
- Observe the scan tool EBCM Battery Voltage Signal parameter. The reading should be between 12.6 and 15.0 V.
| ⇒ | If not within the specified range, refer to Charging System Test. |
Circuit/System Testing
- Ignition OFF, disconnect the harness connector at the module that set the DTC.
- Ignition OFF and scan tool disconnected, open and close the drivers door, and wait 1 minute. Test for less than 5 Ω between the ground circuit terminals listed below and ground.
- Verify that a test lamp illuminates between the B+ circuit terminals listed below and ground.
- If all circuits test normal, replace the EBCM.
| • | Terminal 11 (JH6/JH7 EBCM) |
| • | Terminal 28 (JF3/JF7 EBCM) |
| • | Terminal 38 (JL4 EBCM) |
| ⇒ | If greater than the specified range, test the ground circuit for an open/high resistance. |
| • | Terminal 1 (JH6/JH7 EBCM) |
| • | Terminal 25 (JF3/JF7/JL4 EBCM) |
| ⇒ | If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for EBCM replacement, setup and programming.
