GM Service Manual Online
For 1990-2009 cars only

Engine Mount Replacement - Right Side 1500 LY2

Removal Procedure

Caution: When raising or supporting the engine for any reason, do not use a jack under the oil pan, any sheet metal, or the crankshaft pulley. Due to the small clearance between the oil pan and the oil pump screen, jacking against the oil pan may cause the pan to be bent against the pump screen. This will result in a damaged oil pickup unit.


    Object Number: 1701534  Size: SH
  1. Remove the upper intake manifold sight shield. Refer to Upper Intake Manifold Cover Replacement.
  2. If the vehicle is equipped with four wheel drive (4WD), remove the front drive axle. Refer to Differential Carrier Assembly Replacement.
  3. Remove the two lower engine mount to engine bolts (1).
  4. Remove the starter motor. Refer to Starter Motor Replacement.

  5. Object Number: 1963125  Size: SH

    Note: DO NOT raise and/or support the engine by the crankshaft balancer or oil pan.

  6. Place an adjustable (screw type) jack to the tab (1) located on the engine block.

  7. Object Number: 1701531  Size: SH
  8. Remove the engine mount to frame bolts (1).

  9. Object Number: 1701534  Size: SH
  10. Remove the two top engine mount to engine bolts (1).
  11. Using the adjustable jack, raise the engine slightly until there is enough clearance to remove the engine mount.

  12. Object Number: 1701802  Size: SH
  13. Remove the engine mount.

Installation Procedure


    Object Number: 1701802  Size: SH
  1. Position the engine mount to the engine.
  2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1701534  Size: SH
  3. Install the two top engine mount to engine bolts (1).
  4. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).


    Object Number: 1963125  Size: SH
  5. Using the adjustable jack, lower the engine until the engine mount is sitting flush on the frame.
  6. Remove the adjustable jack from the engine block lifting tab (1).

  7. Object Number: 1701531  Size: SH
  8. Install the engine mount to frame bolts (1).
  9. Tighten
    Tighten the bolts to 65 N·m (48 lb ft) starting with the middle bolt then either side bolt.

  10. Install the starter motor. Refer to Starter Motor Replacement.

  11. Object Number: 1701534  Size: SH
  12. Install the two lower engine mount to engine bolts (1).
  13. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).

  14. If the vehicle is equipped with 4WD, Install the front drive axle. Refer to Differential Carrier Assembly Replacement.
  15. Install the upper intake manifold sight shield. Refer to Upper Intake Manifold Cover Replacement.

Engine Mount Replacement - Right Side 1500 Except RPOs LY6, LY2

Removal Procedure

Caution: When raising or supporting the engine for any reason, do not use a jack under the oil pan, any sheet metal, or the crankshaft pulley. Due to the small clearance between the oil pan and the oil pump screen, jacking against the oil pan may cause the pan to be bent against the pump screen. This will result in a damaged oil pickup unit.


    Object Number: 1701534  Size: SH
  1. Remove the upper intake manifold sight shield. Refer to Upper Intake Manifold Cover Replacement.
  2. If the vehicle is equipped with four wheel drive (4WD), remove the front drive axle. Refer to Differential Carrier Assembly Replacement.
  3. Remove the two lower engine mount to engine bolts (1).
  4. Remove the starter motor. Refer to Starter Motor Replacement.

  5. Object Number: 1963125  Size: SH

    Note: DO NOT raise and/or support the engine by the crankshaft balancer or oil pan.

  6. Place an adjustable (screw type) jack to the tab (1) located on the engine block.

  7. Object Number: 1701531  Size: SH
  8. Remove the engine mount to frame bolts (1).

  9. Object Number: 1701534  Size: SH
  10. Remove the two top engine mount to engine bolts (1).
  11. Using the adjustable jack, raise the engine slightly until there is enough clearance to remove the engine mount.

  12. Object Number: 1701536  Size: SH
  13. Remove the engine mount.

Installation Procedure


    Object Number: 1701536  Size: SH
  1. Position the engine mount to the engine.
  2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1701534  Size: SH
  3. Install the two top engine mount to engine bolts (1).
  4. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).


    Object Number: 1963125  Size: SH
  5. Using the adjustable jack, lower the engine until the engine mount is sitting flush on the frame.
  6. Remove the adjustable jack from the engine block lifting tab (1).

  7. Object Number: 1701531  Size: SH
  8. Install the engine mount to frame bolts (1).
  9. Tighten
    Tighten the bolts to 65 N·m (48 lb ft) starting with the middle bolt then either side bolt.

  10. Install the starter motor. Refer to Starter Motor Replacement.

  11. Object Number: 1701534  Size: SH
  12. Install the two lower engine mount to engine bolts (1).
  13. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).

  14. If the vehicle is equipped with 4WD, Install the front drive axle. Refer to Differential Carrier Assembly Replacement.
  15. Install the upper intake manifold sight shield. Refer to Upper Intake Manifold Cover Replacement.

Engine Mount Replacement - Right Side 2500 LY6

Removal Procedure

Caution: When raising or supporting the engine for any reason, do not use a jack under the oil pan, any sheet metal, or the crankshaft pulley. Due to the small clearance between the oil pan and the oil pump screen, jacking against the oil pan may cause the pan to be bent against the pump screen. This will result in a damaged oil pickup unit.


    Object Number: 1701900  Size: SH
  1. Remove the upper intake manifold sight shield. Refer to Upper Intake Manifold Cover Replacement.
  2. If the vehicle is equipped with four wheel drive (4WD), remove the front drive axle. Refer to Differential Carrier Assembly Replacement.
  3. Remove the two lower engine mount to engine bolts (1).
  4. Remove the starter motor. Refer to Starter Motor Replacement.

  5. Object Number: 1963125  Size: SH

    Note: DO NOT raise and/or support the engine by the crankshaft balancer or oil pan.

  6. Place an adjustable (screw type) jack to the tab (1) located on the engine block.

  7. Object Number: 1701898  Size: SH
  8. Remove the engine mount to frame bolts (1).

  9. Object Number: 1701900  Size: SH
  10. Remove the two top engine mount to engine bolts (1).
  11. Using the adjustable jack, raise the engine slightly until there is enough clearance to remove the engine mount.

  12. Object Number: 1701903  Size: SH
  13. Remove the engine mount.

Installation Procedure


    Object Number: 1701903  Size: SH
  1. Position the engine mount to the engine.
  2. Caution: Refer to Fastener Caution in the Preface section.


    Object Number: 1701900  Size: SH
  3. Install the two top engine mount to engine bolts (1).
  4. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).


    Object Number: 1963125  Size: SH
  5. Using the adjustable jack, lower the engine until the engine mount is sitting flush on the frame.
  6. Remove the adjustable jack from the engine block lifting tab (1).

  7. Object Number: 1701898  Size: SH
  8. Install the engine mount to frame bolts (1).
  9. Tighten
    Tighten the bolts to 65 N·m (48 lb ft) starting with the middle bolt then either side bolt.

  10. Install the starter motor. Refer to Starter Motor Replacement.

  11. Object Number: 1701900  Size: SH
  12. Install the two lower engine mount to engine bolts (1).
  13. Tighten
    Tighten the bolts to 50 N·m (37 lb ft).

  14. If the vehicle is equipped with 4WD, Install the front drive axle. Refer to Differential Carrier Assembly Replacement.
  15. Install the upper intake manifold sight shield. Refer to Upper Intake Manifold Cover Replacement.