Remote Control Door Lock Receiver Scan Tool Information. Chevrolet Silverado

For 1990-2009 cars only

Makes 🢒 Chevrolet 🢒 2009 🢒 Silverado - 4WD 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 Remote Control Door Lock Receiver Scan Tool Information

Table 1:	Remote Control Door Lock Receiver Scan Tool Data Parameters
Table 2:	Remote Control Lock Receiver Scan Tool Output Controls

Remote Control Door Lock Receiver Scan Tool Data Parameters

Parameter	Expected Value	Definition
Operating Conditions: Ignition ON
Fob 1 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 1 battery.
Fob 1 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 1 command as monitored by the RCDLR.
Fob 1 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 1 is programmed into the RCDLR.
Fob 2 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 2 battery.
Fob 2 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 2 command as monitored by the RCDLR.
Fob 2 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 2 is programmed into the RCDLR.
Fob 3 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 3 battery.
Fob 3 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 3 command as monitored by the RCDLR.
Fob 3 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 3 is programmed into the RCDLR.
Fob 4 Battery	OK	The scan tool displays OK or Low. This is the state of the Fob 4 battery.
Fob 4 Function	None	The scan tool displays None, Lock, Dr Door Unlock, All Door Unlock, R Closure Rel., Lt Sliding Ctrl., Rt Sliding Ctrl., Panic, Fuel Door, Power Window, Power Top, Engine Start, Engine Stop, Fob Program, Locate, R Closure Close, R Closure Open, R Closure Stop, Double Lock, R Closure Start or Lt Sliding Stop. This is the state of the Fob 4 command as monitored by the RCDLR.
Fob 4 Programmed	Yes	The scan tool displays Yes or No. Yes is displayed if the Fob 4 is programmed into the RCDLR.
Front Placard	Varies	This displays Counts.
Last Fob Used	Varies	The scan tool displays None, Fob 1, Fob 2, Fob 3, Fob 4 or Fob 5. This was the last Fob used, as monitored by the RCDLR.
Learn in Progress	Yes	The scan tool displays Yes or No. This is the status of the key fob.
LF Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the left front pressure sensor.
LF Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the left front tire pressure.
LF Tire Press. Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the left front tire pressure sensor.
LF Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the left front tire.
LF Tire Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the left front tire pressure sensor.
LR Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the left rear pressure sensor.
LR Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the left rear tire pressure.
LR Tire Press. Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the left rear tire pressure sensor.
LR Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the left rear tire.
LR Tire Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the left rear tire pressure sensor.
Rear Placard	Varies	This displays Counts.
RF Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the right front pressure sensor.
RF Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the right front tire pressure.
RF Tire Press. Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the right front tire pressure sensor.
RF Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the right front tire.
RF Tire Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the right front tire pressure sensor.
RR Pressure Sensor Mode	Varies	The scan tool displays Learn, Re-measure, Rolling, Entering Off or Exiting Off. This is the state of the right rear pressure sensor.
RR Pressure Status	Normal	The scan tool displays Unknown, Normal, Low, Flat or High. This is the state of the right rear tire pressure.
RR Tire Press. Sensor Status	Normal	The scan tool displays Normal or Failed. This is the state of the right rear tire pressure sensor.
RR Tire Pressure	Varies	This displays kPa (psi). This is the amount of pressure in the right rear tire.
RR Tire Pressure Sensor Battery Status	OK	The scan tool displays OK or Low. This is the state of the battery in the right rear tire pressure sensor.
Selected Front Tire Type	Varies	The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of front tires used on the vehicle.
Selected Rear Tire Type	Varies	The scan tool displays N/A, P-Metric (S), P-Metric (X), Load Range C, Load Range D or Load Range E. This is the type of rear tires used on the vehicle.
TPM Indicator/Message	Off	The scan tool displays On or Off. This is the state of the TPM indicator.
TPM System Enabled	Yes	The scan tool displays Yes or No. Yes is displayed if the TPM system is enabled.

Remote Control Lock Receiver Scan Tool Output Controls

Scan Tool Output Control	Description
Copy and Paste TPM Information	This procedure copies existing setup information from the module.
Invalidate All Fobs	This program will erase all key fobs from memory and then begin reprogramming.
Next Available Slot	This program will add key fobs being programmed to the first open slot available in the module.
Program Key Fob 1	Place module in program mode. Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Program Key Fob 2	Place module in program mode. Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Program Key Fob 3	Place module in program mode. Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Program Key Fob 4	Place module in program mode. Repeatedly press and hold the Lock/Unlock buttons on the key fob.
Tire/Type/Pressure Selection	Select load range from list. Select recommended front tire pressure. Select recommended rear tire pressure.