Fuel Gage Inaccurate or Inoperative Single Tank

The fuel level sensor changes resistance in response to the fuel level. The engine control module (ECM) monitors the signal circuit of the fuel level sensor in order to determine the fuel level. When the fuel tank is full, the sensor resistance is low and the ECM senses a low signal voltage. When the fuel tank is empty, the sensor resistance is high and the ECM senses a high signal voltage. The ECM uses the signal circuit of the fuel level sensor in order to calculate the percentage of remaining fuel in the tank. The ECM sends the fuel level percentage via the serial data circuit to the body control module (BCM). The BCM then sends the fuel information to the instrument panel cluster (IPC) via the serial data circuit in order to display the fuel gage.

Schematic Reference

Instrument Cluster Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Instrument Cluster Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

Ignition ON, verify DTC P0461, P0462, P0463, or P0464 is not set

1. Ignition OFF, disconnect the harness connector at the fuel level sensor.
2. Ignition OFF, test for less than 1.0 ohm between the low reference circuit terminal B and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Install a Signal Generator and Instrument Panel Tester between the signal circuit terminal C and the low reference circuit terminal B.
4. Ignition ON, vary the signal generator resistance between 40-250 ohms. Verify that the scan tool Fuel Tank Level Remaining parameter displays a range that varies between 5 and 95 percent as the signal generator resistance changes.

⇒	If not within the specified range, test the signal circuit for an open/high resistance. If the circuits test normal, replace the ECM.

5. Vary the signal generator resistance between 40-250 ohms. Verify that the fuel gage displays a range that varies between empty and full as the signal generator resistance changes.

⇒	If the gage is incorrect, replace the IPC.

6. If all circuits test normal, perform the fuel level sensor component test before replacing the fuel level sensor.

1. Ignition OFF, remove the fuel level sender.
2. While sweeping the fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms between the signal terminal C and the low reference terminal B.

⇒	If not within the specified range, replace the fuel level sensor.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Fuel Gage Inaccurate or Inoperative Dual Tank

The fuel level sensor changes resistance in response to the fuel level. The engine control module (ECM) monitors the signal circuits of the primary and secondary fuel level sensors in order to determine the fuel level. When the fuel tanks are full, the sensor resistances are low and the ECM senses a low signal voltage. When the fuel tanks are empty, the sensor resistances are high and the ECM senses a high signal voltage. The ECM uses the signal circuits of the primary and secondary fuel level sensors in order to calculate the percentage of remaining fuel in the tanks. The ECM sends the fuel level percentage via the serial data circuit to the body control module (BCM). The BCM then sends the fuel level information to the instrument panel cluster (IPC) the serial data circuit in order to display the fuel level.

Schematic Reference

Instrument Cluster Schematics

Connector End View Reference

Component Connector End Views

Description and Operation

Instrument Cluster Description and Operation

Electrical Information Reference

Scan Tool Reference

Control Module References for scan tool information

Ignition ON, verify DTC P0461, P0462, P0463, P0464, P2066, P2067, or P2068 is not set

1. Ignition OFF, disconnect the harness connector at the primary and secondary fuel level sensors.
2. Ignition OFF, test for less than 1.0 ohm between the primary fuel level sensor low reference circuit terminal B and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

3. Ignition OFF, test for less than 1.0 ohm between the secondary fuel level sensor low reference circuit terminal B and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

4. Jumper the primary fuel level sensor signal circuit terminal C to secondary fuel level sensor signal circuit terminal C. Install a Signal Generator and Instrument Panel Tester between the jumped signal circuits and the low reference circuit terminal B.
5. Ignition ON, vary the signal generator resistance between 40-250 ohms. Verify that the scan tool Fuel Tank Level Remaining parameter displays a range that varies between 5 and 95 percent as the signal generator resistance changes.

⇒	If not within the specified range, test both signal circuits for an open/high resistance. If the circuits test normal, replace the ECM.

6. Vary the signal generator resistance between 40-250 ohms. Verify that the fuel gage displays a range that varies between empty and full as the signal generator resistance changes.

⇒	If the gage is incorrect, replace the IPC.

7. If all circuits test normal, perform the fuel level sensor component test before replacing either the primary or secondary fuel level sensor.

1. Ignition OFF, remove the primary and secondary fuel level senders.
2. While sweeping the primary fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms between the signal terminal C and the low reference terminal B.

⇒	If not within the specified range, replace the primary fuel level sensor.

3. While sweeping the secondary fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms between the signal terminal C and the low reference terminal B.

⇒	If not within the specified range, replace the secondary fuel level sensor.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.