1

Endgate Nameplate

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from the endgate and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
4. Position the new nameplate to the left upper side of the endgate.
5. Using the palm of the hand, wet out the name plate to the endgate and ensure full adhesion of the nameplate is made.

1

Endgate Nameplate

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from bodyside panel and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
4. Using the palm of the hand, wet out the name plate to the body side and ensure full adhesion of the nameplate is made.

1

Endgate Nameplate/Emblem (LT)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

2

Endgate Nameplate/Emblem (LS)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate/emblem. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates/emblems, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

1

Endgate Nameplate/Emblem (Silverado)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

2

Endgate Nameplate/Emblem (Cheyenne)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate/emblem. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates/emblems, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

1

Endgate Nameplate/Emblem (Sierra)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

2

Endgate Nameplate/Emblem (GMC)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate/emblem. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates/emblems, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

1

Endgate Nameplate

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. The part and surface should be 21°C (70°F) prior to installation. The vehicle should remain 21°C (70°F) for one hour after assembly to allow adhesive to develop sufficient bond strength.
2. Use a J 25070 Heat Gun or equivalent to remove the old nameplate. Clean all adhesive from the endgate and wipe the surface dry with a clean lint-free towel prior to installing the new name plate.
3. When removing protective liners from the adhesive tape, be careful not to touch tape with hands and do not allow tape to come in contact with dirt or any foreign matter prior to adhesion.
4. Using the palm of the hand, wet out the name plate to the endgate and ensure full adhesion of the nameplate is made.

1

Endgate Nameplate/Emblem (Z71)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

1

Endgate Nameplate/Emblem (SLT)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.

2

Endgate Nameplate/Emblem (SLE)

Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

Procedure

1. Use a J 25070 or equivalent to remove the old nameplate/emblem. Clean all the adhesive residue from the endgate, wipe the surface dry with a clean lint-free towel prior to installing new nameplate.
2. When removing protective liners from adhesive backed nameplates/emblems, be careful not to touch the tape with hands and do not allow the tape to come in contact with dirt or any foreign matter prior to adhesion.
3. Close the endgate prior to installing the new nameplate/emblem to the endgate.
4. Remove the protective liner from the back side of the adhesive tape.
5. Align the nameplate/emblem to the endgate and press to ensure full adhesion is made.