GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Silverado - 4WD 🢒 Steering 🢒 Steering Wheel and Column 🢒 Steering Shaft Upper Bearing Replacement

Special Tools

    • J 21854-01 Pivot Pin Remover
    • J 23653-SIR Steering Column Lock Plate Compressor
    • J 42137 Cam Orientation Plate Adapter
    • J 42640 Steering Column Anti-Rotation Pin

Removal Procedure

    Warning: Refer to SIR Warning in the Preface section.

  1. Remove the steering column. Refer to Steering Column Replacement.
  2. Remove the inflatable restraint steering wheel module coil. Refer to Steering Wheel Inflatable Restraint Module Coil Replacement.
  3. Remove the turn signal multifunction switch. Refer to Turn Signal Multifunction Switch Replacement.
  4. Remove the ignition lock cylinder case. Refer to Ignition Lock Cylinder Case Replacement.
  5. Remove the tilt spring. Refer to Steering Column Tilt Spring Replacement.
  6. Remove the automatic transmission control. Refer to Transmission Control Replacement.

    7. Object Number: 338052 Size: SH
  7. Using compressor J 23653-SIR and adapter J 42137 , remove and discard the steering shaft lock plate retaining ring.

    8. Object Number: 664265 Size: SH
  8. Remove the following parts from the steering column shaft assembly:
    9. 8.1. The turn signal switch cancel cam position plate (5)
    8.2. The turn signal switch cancel cam (4)
    8.3. The steering shaft upper bearing spring (3)
    8.4. The steering shaft upper bearing inner race seat (2)
    8.5. The steering shaft upper bearing inner race (1)

    Object Number: 306307 Size: SH
  9. Remove the 2 pivot pins (3) from the steering column tilt head assembly (1) by using remover J 21854-01  (2).

    10. Object Number: 1730627 Size: SH
  10. Install the tilt lever into the steering column tilt head assembly (1).
  11. Pull back on the tilt lever and at the same time, pull the steering column tilt head assembly (1) down and away from the steering column.
  12. Remove the steering column tilt head assembly.
  13. Remove anti-rotation pin J 42640 .
  14. Remove the tilt lever.

    15. Object Number: 1562300 Size: SH
  15. Remove the steering shaft upper bearing from the steering column tilt head assembly.

Installation Procedure

    Object Number: 1562300 Size: SH
  1. Install the steering shaft upper bearing to the steering column tilt head assembly.

    2. Object Number: 1730627 Size: SH
  2. Install the steering column shaft assembly.
  3. Maneuver and push the steering column tilt head assembly (1) towards the steering column in order to lock the steering wheel lock shoes in place.

    4. Object Number: 299893 Size: SH
  4. Lubricate the pivot pins (1) with GM P/N 12346293 (Canadian P/N 992723).
  5. Firmly seat each pivot pin (1) into the steering column tilt head assembly.
  6. Stake the steering column in 3 locations around each pivot pin.
  7. Install anti-rotation pin J 42640 .

    8. Object Number: 664265 Size: SH
  8. Install the following parts onto the steering column shaft assembly:
    9. 8.1. Lubricate the steering shaft upper bearing inner race (1) with GM P/N 12345718 (Canadian P/N 10953516).
    8.2. The steering shaft upper bearing inner race (1)
    8.3. The steering shaft upper bearing inner race seat (2)
    8.4. The steering shaft upper bearing spring (3)
    8.5. Lubricate the turn signal switch cancel cam (4) with GM P/N 12377900 (Canadian P/N 10953529).
    8.6. The turn signal switch cancel cam  (4)
    8.7. The turn signal switch cancel cam position plate (5)

    Object Number: 338052 Size: SH
  9. Install the new steering shaft lock plate retaining ring onto the steering shaft using compressor J 23653-SIR and adapter J 42137 .
  10. Install the automatic transmission control assembly. Refer to Transmission Control Replacement.
  11. Install the tilt spring. Refer to Steering Column Tilt Spring Replacement.
  12. Install the ignition lock cylinder case. Refer to Ignition Lock Cylinder Case Replacement.
  13. Install the turn signal multifunction switch. Refer to Turn Signal Multifunction Switch Replacement.
  14. Install the inflatable restraint steering wheel module coil. Refer to Steering Wheel Inflatable Restraint Module Coil Replacement.
  15. Install the steering column. Refer to Steering Column Replacement.