The manifold absolute pressure (MAP) sensor responds to pressure changes in the intake manifold. The pressure changes occur based on the engine load. The engine control module (ECM) supplies 5 volts to the MAP sensor on the 5-volt reference circuit. The ECM provides a ground on the low reference circuit. The MAP sensor provides a signal to the ECM on the MAP sensor signal circuit which is relative to the pressure changes in the manifold. The ECM detects a low signal voltage at a low MAP, such as during an idle or a deceleration. The ECM detects a high signal voltage at a high MAP, such as the ignition is ON, with the engine OFF, or at a wide open throttle (WOT). The MAP sensor is also used to determine the barometric pressure (BARO). This occurs when the ignition switch is turned ON, with the engine OFF. The BARO reading may also be updated whenever the engine is operated at WOT. The MAP sensor contains the following circuits:
• | A 5-volt reference |
• | A low reference |
• | A MAP sensor signal |
If the ECM detects that the MAP sensor pressure/voltage is too low, this DTC sets.
This diagnostic procedure supports the following DTC:
DTC P0107 Manifold Absolute Pressure (MAP) Sensor Circuit Low Voltage.
• | No throttle position (TP) sensor or idle speed control (ISC) DTCs. |
• | The engine speed is less than 2,500 RPM. |
• | DTC P0107 runs continuously once the above conditions are met. |
• | No TP sensor DTCs. |
• | The TP sensor angle is more than 30.0 degrees. |
• | The engine speed is less than 4,000 RPM. |
• | DTC P0107 runs continuously once the above conditions are met. |
An open or short to ground condition exists.
• | The malfunction indicator lamp (MIL) will illuminate. |
• | The ECM will record operating conditions at the time the diagnostic fails. This information will be stored in the Freeze Frame and Failure Records buffers. |
• | A history DTC is stored. |
• | The coolant fan turns ON. |
• | The ECM will substitute a fixed MAP value and use the TP to control the fuel delivery. The scan tool will not show defaulted. |
• | The malfunction indicator lamp (MIL) will illuminate. |
• | The ECM will substitute a fixed MAP value and use the TP to control the fuel delivery. The scan tool will not show the defaulted value. |
• | The MIL will turn OFF after 4 consecutive ignition cycles in which the diagnostic runs without a fault. |
• | A history DTC will clear after 40 consecutive warm-up cycles without a fault. |
• | DTCs can be cleared by using the scan tool. |
• | Disconnect the ECM battery feed for more than 10 seconds. |
• | The MIL will turn OFF when the diagnostic runs and passes. |
• | DTCs can be cleared by using the scan tool. |
• | Disconnect the ECM battery feed for more than 10 seconds. |
• | If a shared 5-volt reference circuit is shorted to ground or shorted to a voltage, the other 5-volt reference circuits may be affected. |
• | For an intermittent condition, refer to Intermittent Conditions . |
Step | Action | Values | Yes | No | ||||||
---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | ||||||||||
1 | Did you perform the Diagnostic System Check - Engine Controls? | -- | Go to Step 2 | |||||||
2 |
Did DTC P0107 fail this ignition? | -- | Go to Step 4 | Go to Step 3 | ||||||
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Diagnostic Aids | ||||||
4 |
Is the voltage within the specified range? | 4.8-5.2 V | Go to Step 5 | Go to Step 6 | ||||||
5 |
Is the pressure more than the specified value? | 102 kPa | Go to Step 8 | Go to Step 7 | ||||||
6 |
Important: The 5-volt reference circuits are internally and externally connected at the ECM. Other component DTCs may be set. If other DTCs are set, review the electrical schematic and diagnose the applicable circuits and components. Test the 5-volt reference circuit of the MAP sensor for the following conditions:
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 | ||||||
7 | Test the signal circuit of the MAP sensor for the following conditions:
Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 | ||||||
8 | Test for an intermittent and for a poor connection at the MAP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 | ||||||
9 | Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 | ||||||
10 | Replace the MAP sensor. Refer to Manifold Absolute Pressure Sensor Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||
11 | Replace the ECM. Refer to Diagnostic Trouble Code (DTC) List . Did you complete the replacement? | -- | Go to Step 12 | -- | ||||||
12 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 13 | ||||||
13 | Are there any DTCs that have not been diagnosed? | -- | System OK |