GM Service Manual Online
For 1990-2009 cars only

Drive Pinion and Ring Gear Replacement 8.6 Inch, 9.5 Inch, 11.5 Inch Axles

Tools Required

    • J 22536 Pinion Remover (8.6 inch, 9.5 inch axles)
    • J 44421 Pinion Remover (11.5 inch axle)

Removal Procedure

  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the tire and wheel assemblies (8.6 inch, 9.5 inch axles). Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  3. Remove the brake calipers (8.6 inch, 9.5 inch axles). Refer to Rear Brake Caliper Replacement in Disc Brakes.
  4. Remove the brake rotors (8.6 inch, 9.5 inch axles). Refer to Rear Brake Rotor Replacement in Disc Brakes.
  5. Remove the axle shafts. Refer to Rear Axle Shaft Replacement (8.6 inch, 9.5 inch axles) or Rear Axle Shaft and/or Gasket Replacement (11.5 inch axles).
  6. Remove the differential. Refer to Differential Replacement .
  7. Remove the pinion yoke and the seal. Refer to Drive Pinion Flange/Yoke and/or Oil Seal Replacement .

  8. Object Number: 683960  Size: SH
  9. Install the J 22536 (8.6 inch, 9.5 inch axle) or the J 44421 (11.5 inch axle) as shown.
  10. Ensure that the J 22536 or the J 44421 is firmly seated on the pinion.

  11. Drive the pinion out using the J 22536 (8.6 inch, 9.5 inch axle) or the J 44421 (11.5 inch axle) and a hammer.
  12. Strike the J 22536 or the J 44421 slowly. Do not let the pinion fall out of the rear axle housing.


    Object Number: 9731  Size: SH
  13. Remove the collapsible spacer from the pinion. Discard the spacer.
  14. Remove the pinion bearings and the cups. Refer to Drive Pinion Bearings Replacement .
  15. Important: The ring gear bolts on the 8.6 inch, the 9.5 inch, and the 10.5 inch axles have left-hand threads. The ring gear bolts on the 11.5 inch axle have right-hand threads.

  16. Remove the gear bolts. Discard the bolts.
  17. Notice: Do not pry the ring gear from the differential case. Prying the ring gear from the differential case may cause damage to the ring gear and/or the differential case.

  18. Remove the ring gear from the differential. Drive the gear off with a brass drift if necessary.

Installation Procedure

    Important: The mating surface of the ring gear and the differential case must be clean and free of burrs before installing the ring gear.


    Object Number: 6940  Size: SH
  1. Install the ring gear to the differential case.
  2. Install two threaded studs into the ring gear on opposite sides.
  3. Place the ring gear on the case. Align the studs with the holes in the case.
  4. Notice: Refer to Fastener Notice in the Preface section.

  5. Install the new left-hand threaded ring gear bolts. Tighten the ring gear bolts alternately and in stages, gradually pulling the ring gear onto the differential case.
  6. Tighten

        • For the 8.6 inch axle, tighten the ring gear bolts in sequence to 120 N·m (89 lb ft).
        • For the 9.5 inch axle, tighten the ring gear bolts in sequence to 140 N·m (103 lb ft).
        • For the 11.5 inch axle, tighten the ring gear bolts in sequence to 237 N·m (175 lb ft).
  7. Install the pinion bearing cups. Refer to Drive Pinion Bearings Replacement .
  8. Determine the selective shim thickness for the pinion gear. Refer to Pinion Depth Adjustment .
  9. Install the selective shim onto the pinion.
  10. Install the inner pinion bearing to the pinion. Refer to Drive Pinion Bearings Replacement .
  11. Install a new collapsible spacer.
  12. Lubricate the pinion bearings with axle lubricant. Refer to Fluid and Lubricant Recommendations in Maintenance and Lubrication.
  13. Install the pinion to the axle housing.
  14. Install the outer pinion bearing onto the pinion.
  15. Install a new pinion oil seal and the pinion yoke. Refer to Drive Pinion Flange/Yoke and/or Oil Seal Replacement .
  16. Install the differential. Refer to Differential Replacement .
  17. Perform a gear tooth contact pattern check on the pinion and the ring gear. Refer to Gear Tooth Contact Pattern Inspection .
  18. Install the axle shafts. Refer to Rear Axle Shaft Replacement (8.6 inch, 9.5 inch axle) or Rear Axle Shaft and/or Gasket Replacement (11.5 inch axle).
  19. Install the brake rotors (8.6 inch, 9.5 inch axle). Refer to Rear Brake Rotor Replacement in Disc Brakes.
  20. Install the brake calipers (8.6 inch, 9.5 inch axle). Refer to Rear Brake Caliper Replacement in Disc Brakes.
  21. Install the tire and wheel assemblies (8.6 inch, 9.5 inch axle). Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  22. Fill the axle with lubricant. Use the proper fluid. Refer to Approximate Fluid Capacities and Fluid and Lubricant Recommendations in Maintenance and Lubrication.
  23. Lower the vehicle.

Drive Pinion and Ring Gear Replacement 10.5 Inch Axle

Removal Procedure

  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the differential. Refer to Differential Replacement .
  3. Remove the pinion gear bearing retainer. Refer to Drive Pinion Housing and/or Seal Replacement .
  4. Remove the pinion and the pinion bearings. Refer to Drive Pinion Housing and/or Seal Replacement .

  5. Object Number: 739940  Size: SH
  6. Remove the left handed threaded ring gear bolts. Discard the bolts.
  7. Notice: Do not pry the ring gear from the differential case. Prying the ring gear from the differential case may cause damage to the ring gear and/or the differential case.

  8. Remove the ring gear from the differential. Drive the gear off with a brass drift if necessary.

Installation Procedure


    Object Number: 739964  Size: SH
  1. If the differential case has become separated, assemble the differential case by aligning the two arrows inside the differential case as shown.
  2. Important: The mating surface of the ring gear and the differential case must be clean and free of burrs before installing the ring gear.

  3. Install the ring gear to the differential case.
  4. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 739940  Size: SH
  5. Install the new left-hand threaded ring gear bolts. Tighten the ring gear bolts alternately and in stages, gradually pulling the ring gear onto the differential case.
  6. Tighten
    Tighten the ring gear bolts in sequence to 165 N·m (122 lb ft).

  7. Install the pinion and the pinion bearings. Refer to Drive Pinion Housing and/or Seal Replacement .
  8. Install the pinion gear bearing retainer. Refer to Drive Pinion Housing and/or Seal Replacement .
  9. Install the differential. Refer to Differential Replacement .
  10. Lower the vehicle.