Power Steering Pump Replacement 4.8L, 5.3L, and 6.0L
Removal Procedure
- Remove the power steering pulley. Refer to
Power Steering Pump Pulley Replacement
.
- Raise the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Remove the oil pan skid plate bolts.
- Remove the oil pan skid plate from the vehicle, if equipped.
- Place a drain pan under the vehicle.
- Remove the power steering pressure hose (2) from the power steering pump from underneath the vehicle.
- Lower the vehicle.
- Remove the clamp (5) retaining the power steering return hose to the power steering pump and remove the hose (4).
- If equipped with hydroboost, remove clamp (3) and disconnect hose (2) from pump.
- Remove the lower intermediate shaft from the steering gear. Refer to
Lower Intermediate Steering Shaft Replacement
.
- Remove the bolt retaining the rear bracket to the engine.
- Remove the bolts from the front of the pump.
- Remove the pump from the vehicle.
- Remove the bracket (3) from the rear of the pump (1).
Installation Procedure
Notice: Refer to Fastener Notice in the Preface section.
- Install the bracket (3) to the rear of the pump (1).
Tighten
Tighten the rear bracket retaining nuts to 50 N·m (37 lb ft).
- Install the power steering pump.
- Install the bolt retaining the rear bracket to the engine.
Tighten
Tighten the rear power steering bracket bolt to engine bracket to 50 N·m (37 lb ft).
- Install the bolts to the front of the pump.
Tighten
Tighten the bolts to 50 N·m (37 lb ft).
- Install the power steering pump return hose (4) to the power steering pump and install the retaining clamp (5).
- If equipped with hydroboost, connect the hose (2) to pump and position the clamp (3)
- Raise the vehicle. Refer to
Lifting and Jacking the Vehicle
.
- Install the power steering pressure hose (2) to the power steering pump.
Tighten
Tighten the fitting to 28 N·m (20 lb ft).
- Install the oil pan skid plate, if equipped.
- Install the oil pan skid plate bolts.
Tighten
Tighten the retaining bolts to 20 N·m (15 lb ft).
- Lower the vehicle.
- Install the intermediate shaft. Refer to
Lower Intermediate Steering Shaft Replacement
.
- Install the power steering pulley. Refer to
Power Steering Pump Pulley Replacement
.
- Fill and bleed the power steering system. Refer to
Power Steering System Bleeding
.
- Refer to
Control Module References
for programming and setup information.
Power Steering Pump Replacement 8.1L
Removal Procedure
- Place a drain pan under the vehicle.
- Remove the power steering pulley. Refer to
Power Steering Pump Pulley Replacement
.
- Remove the nut (1) and clamp (3) retaining the filler neck (1) to the power steering pump, if equipped.
- Remove the bolts (2) from the front of the pump.
- Remove the bolts retaining the power steering mounting bracket.
- Remove the bolts (1) from the rear of the pump.
- Remove the power steering return hoses (2,4) from the power steering pump.
- Remove the power steering pressure hoses (2) from the power steering pump.
- Remove the pump from the vehicle.
- Remove the rear bracket from the power steering pump.
Installation Procedure
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the rear bracket to the power steering pump.
Tighten
Tighten the rear bracket retaining nuts to 50 N·m (37 lb ft).
- Install the power steering pump to the vehicle.
- Install the pressure hose (2) to the power steering pump.
Tighten
Tighten the hose fitting to 28 N·m (20 lb ft).
- Install the power steering return hoses (2,4) and retaining clamps to the power steering pump.
- Install the bolts (1) to the rear of the power steering pump.
Tighten
Tighten the rear bolts to 50 N·m (37 lb ft).
- Install the power steering pump mounting bracket bolts.
Tighten
Tighten the mounting bracket bolts to 50 N·m (37 lb ft).
- Install the bolts (2) to the front of the pump.
Tighten
Tighten the power steering pump retaining bolts to 50 N·m (37 lb ft).
- Install the filler neck to the power steering pump.
- Install the nut (1) and clamp (3) retaining the filler neck to the power steering pump.
Tighten
Tighten the filler neck retaining nut to 25 N·m (18 lb ft).
- Fill and bleed the power steering system. Refer to
Power Steering System Bleeding
.
- Refer to
Control Module References
for programming and setup information.