Locking Differential Cam Unit Assemble 8.6 Inch Axle
- Apply axle lubricant to the locking differential clutch (friction disc) contact area. Refer to
Adhesives, Fluids, Lubricants, and Sealers.
- Install the locking differential cam (3) on the locking differential side gear (2).
- Install the locking differential clutch disc set (1) on the locking differential side gear (2).
- Compress the locking differential clutch disc set assembly.
- Using the appropriate tool, install the external span ring retainer.
Note: Applying a small amount of grease to the locking differential guides will hold them in place during the installation procedure.
- Apply a small amount of chassis grease to hold the locking differential clutch disc guide (5). Refer to
Adhesives, Fluids, Lubricants, and Sealers.
Locking Differential Cam Unit Assemble 9.5 Inch Axle
Special Tools
J 29710 Differential Side Bearing Installer
- Apply axle lubricant to each of the locking differential clutch (friction disc) contact area. Refer to
Adhesives, Fluids, Lubricants, and Sealers.
- Install the locking differential cam (3) on the locking differential side gear (2).
Note: When installing the locking differential clutch disc set, align the splined discs with the teeth on the cam in order to compress the clutch disc assembly.
- Install the locking differential clutch disc set (1) on the locking differential side gear (2).
- Position the locking differential side gear thrust sleeve (5).
Note: If reusing the locking differential side gear thrust sleeve, proceed to step 5. If replacing the locking differential side gear thrust sleeve, proceed to step 6.
- Using the
J 29710 installer
and a hydraulic press, install the locking differential side gear thrust sleeve until it is fully seated on the locking differential side gear.
- If the locking differential cam side gear or the locking differential thrust sleeve has been replaced, measure the overall length of the gear assembly by doing the following:
6.1. | Place the locking differential clutch disc thrust washer on top of the thrust sleeve. |
6.2. | Measure the overall length of the gear assembly from the front of the cam side gear to the back of the locking differential clutch disc thrust washer. |
6.3. | Compare this measurement to the measurement obtained during disassembly. |
6.4. | If the new reading is more than
0.762 mm (0.003 in) higher or lower than the original, select a locking differential clutch disc thrust washer that will return the reading closest to the original reading. |
- Align the ears of all the clutch discs.
Note: Applying a small amount of grease on the locking differential guides will hod them in place during the installation procedure.
- Install the guide clips to the clutch disc assembly and apply chassis grease to the locking differential guides. Refer to
Adhesives, Fluids, Lubricants, and Sealers.
Locking Differential Cam Unit Assemble 10.5 Inch Axle
Special Tools
J 29710 Differential Side Bearing Installer
Differential Side Bearing Installer
- Apply axle lubricant to each of the locking differential clutch (friction disc) contact area. Refer to
Adhesives, Fluids, Lubricants, and Sealers
- Install the locking differential cam (2) on the locking differential side gear (1).
- Install the locking differential clutch disc set (7).
- Position the locking differential side gear thrust sleeve (5) on the locking differential side gear (1).
Note: If reusing locking differential side gear thrust sleeve, proceed to step 5. If replacing the locking differential side gear thrust sleeve, proceed to step 6.
- Using the
J 29710 installer
and a hydraulic press, install the locking differential side gear thrust sleeve until it is fully seated on the locking differential side gear.
- If the cam side gear or the thrust sleeve has been replaced, measure the overall length of the gear assembly by doing the following:
6.1. | Place the locking differential clutch disc thrust washer on top of the thrust sleeve. |
6.2. | Measure the overall length of the gear assembly from the front of the cam side gear to the back of the locking differential clutch disc thrust washer. |
6.3. | Compare this measurement to the measurement obtained during disassembly. |
6.4. | If the new reading is more than
0.762 mm (0.003 in) greater than or less than the original, select a locking differential clutch disc thrust washer that will return the reading closest to the original reading. |
- Align the locking differential clutch disc set.
Note: Applying a small amount of chassis grease to the locking differential guides will hold them in place during the installation procedure.
- Install the and apply a small amount of chassis grease to the locking differential guides. Refer to
Adhesives, Fluids, Lubricants, and Sealers.