• | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
• | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
• | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
---|---|---|---|---|---|
Adjustable Pedal Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 3 | B3920 01 | B1335 42, B1335 4B, B3606 5A |
Adjustable Pedal Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 3 | B3920 01 | B1335 42, B1335 4B, B3606 5A |
Driver Seat Front Vertical Motor Down Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2355 5A |
Driver Seat Front Vertical Motor Up Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2355 5A |
Driver Seat Rear Vertical Motor Down Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2365 5A |
Driver Seat Rear Vertical Motor Up Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2365 5A |
Driver Seat Horizontal Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2375 5A |
Driver Seat Horizontal Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B2375 5A |
Driver Seat Recline Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B1825 5A |
Driver Seat Recline Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 1 | B3920 01 | B1335 42, B1335 4B, B1825 5A |
Driver Seat Lumbar Motor Up Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1335 42, B1335 4B, B1860 5A |
Driver Seat Lumbar Motor Down Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1335 42, B1335 4B, B1860 5A |
Driver Seat Lumbar Motor Forward Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1335 42, B1335 4B, B1850 5A |
Driver Seat Lumbar Motor Rearward Control | B3920 02 | B1335 00, B1335 0B | 2 | B3920 01 | B1335 42, B1335 4B, B1850 5A |
1. Power seat motor inoperative 2. Lumbar motor inoperative 3. Adjustable pedal motor inoperative |
The memory seat module (MSM) monitors the current supplied to the seat adjuster motors. The MSM can detect both absolute and differential current levels from the motors. Absolute current is the maximum allowable current the module will supply to the motors. A differential current mismatch occurs when the current supplied to the seat, lumbar and adjustable pedal motors do not match the current returning from the motors.
The MSM establishes that it is not closing to a shorted motor control circuit before the motors are active.
Current out of the module does not match the current returning to the module within 5 amps.
The absolute current or an over-current has exceeded the maximum value allowed.
This DTC will set if the module calibration is not programmed.
This DTC will set if the module calibration is out of range.
The adjustable pedal motor and all driver seat adjuster motors are disabled.
• | The current DTC will clear and set the code to history, 3 seconds after no motor movement is requested or the current is no longer mismatched, and the ignition is cycled OFF then back to ACC or RUN. |
• | The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred. |
Memory Seats Description and Operation
Control Module References for scan tool information
• | Driver seat front vertical motor |
• | Driver seat rear vertical motor |
• | Driver seat horizontal motor |
• | Driver seat recline motor |
• | Driver seat lumbar horizontal motor |
• | Driver seat lumbar vertical motor |
• | Adjustable pedal motor |
⇒ | If the DTC sets, test for a short between appropriate motor control circuits listed below. If the circuits test normal, replace the MSM. |
• | Front vertical motor terminal 2 and terminal 5 |
• | Rear vertical motor terminal 1 and terminal 4 |
• | Seat horizontal motor terminal 3 and terminal 6 |
• | Seat recline motor terminal A and terminal B |
• | Lumbar vertical motor terminal A and terminal B |
• | Lumbar horizontal motor terminal C and terminal D |
• | Adjustable pedal motor terminal 4 and terminal 5 |
• | Front vertical motor terminal 2 and terminal 5 |
• | Rear vertical motor terminal 1 and terminal 4 |
• | Seat horizontal motor terminal 3 and terminal 6 |
• | Seat recline motor terminal A and terminal B |
• | Lumbar vertical motor terminal A and terminal B |
• | Lumbar horizontal motor terminal C and terminal D |
• | Adjustable pedal motor terminal 4 and terminal 5 |
Verify that DTC B1335 42 or B1335 4B is not set.
⇒ | If either DTCs is set, replace the MSM. |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
• | Control Module References for MSM replacement, setup, and programming |