GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Chevrolet 🢒 2009 🢒 Tahoe - 2WD 🢒 Body Repair 🢒 Bolted Exterior Body Panels and Closures 🢒 Decal or Stripe Replacement

Decal or Stripe Replacement Tahoe Hybrid 2 Mode Lower Door


Object Number: 2046763 Size: MF

Callout

Component Name

Preliminary Procedures

  1. Using a J 25070 or equivalent, in a circular motion, remove the old decal from both lower door panels.
  2. Remove all adhesives as follows:
    3. • For metal body panels use a 3M Scotch Brite® molding adhesive remover disc, 3M P/N 07502 or equivalent.
    • For plastic panels use a lint-free cloth with Varnish Makers and Painters (VMP) Naptha or a 50/50 mixture, by volume of isopropyl alcohol and clean drinkable water to remove left over adhesive.
  3. For the final preparation prior to application of the new decal, refer to Graphics/Decals/Emblems.

Special Tools

J 25070 Heat Gun 500-750°F

1

HYBRID Lower Door Decal

Tip
The lower door decal is serviced as one part.

Decal or Stripe Replacement Tahoe Hybrid 2 Mode Rear Glass


Object Number: 2062946 Size: SF

Callout

Component Name

Preliminary Procedures

  1. Heat the decal using a J-25070 gun or equivalent, 152 mm (6 in) from the glass surface.
  2. Apply the heat using a circular motion, for about 30 seconds.

    3. Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

  3. Remove the decal from the surface using a plastic, flat-bladed tool.
  4. Remove all adhesive from the surface using a 3M™ Scotch Brite molding adhesive remover disk, 3M™ P/N 07501, or equivalent.
  5. Clean the surface using 3M™ General Purpose Adhesive Cleaner, P/N 08984 or equivalent.

Special Tools

J-25070 Heat Gun 500-750°F

1

HYBRID Liftgate Glass Decal

Tip
The liftgate glass decal is serviced as one part.

Decal or Stripe Replacement Tahoe Hybrid 2 Mode Windshield


Object Number: 2062949 Size: SF

Callout

Component Name

Preliminary Procedures

  1. Heat the decal using a J-25070 gun or equivalent, 152 mm (6 in) from the glass surface.
  2. Apply the heat using a circular motion, for about 30 seconds.

    3. Caution: Refer to Exterior Trim Emblem Removal Caution in the Preface section.

  3. Remove the decal from the surface using a plastic, flat-bladed tool.
  4. Remove all adhesive from the surface using a 3M™ Scotch Brite molding adhesive remover disk, 3M™ P/N 07501, or equivalent.
  5. Clean the surface using 3M™ General Purpose Adhesive Cleaner, P/N 08984 or equivalent.

Special Tools

J-25070 Heat Gun 500-750°F

1

HYBRID Windshield Glass Decal

Tip
The windshield glass decal is serviced as one part.

Decal or Stripe Replacement Escalade HYBRID 2 Mode Door Decal


Object Number: 2115014 Size: MF

Callout

Component Name

Preliminary Procedures

  1. Using a J 25070 or equivalent, in a circular motion, remove the old decal from both lower door panels.
  2. Remove all adhesives as follows:
    3. • For metal body panels use a 3M Scotch Brite® molding adhesive remover disc, 3M P/N 07502 or equivalent.
    • For plastic panels use a lint-free cloth with Varnish Makers and Painters (VMP) Naptha or a 50/50 mixture, by volume of isopropyl alcohol and clean drinkable water to remove left over adhesive.
  3. For the final preparation prior to application of the new decal, refer to Graphics/Decals/Emblems.

Special Tools

J 25070 Heat Gun 500-750°F

1

HYBRID Lower Door Decal

Tip
The lower door decal is serviced as one part.